Moving PRI and Re-Routing Outbound Calls - PBX Info Forum | Telephony Resource Tech Tips Community for Avaya, Nortel, Cisco, Panasonic, ShoreTel, Asterisk and more...

blkphtm · 07-02-2009

We currently have two sites in which have a point-to-point T1 dedicated for voice traffic. Both sites are using the Toshiba CIX670 system and each have their own PRI. We are taking away our PRI circuit from one of our locations and piping into a new location (which is a non-toshiba system).

We have a 2500 block and a 5600 block of numbers. We have all ready moved the 2500 block of numbers from the PRI that will be going away to a PRI that is connected to our other building that has the Toshiba system and everything is working as it should after importing the DIDs into that system.

My question now is, what will I need to change to pipe Outgoing calls from using the PRI to using the Point-to-Point connection, then out that PRI line???

For Outgoing Line Groups, I have 4 that are in the system now. 2 for Analog, and 2 for ISDN as it is labeled on the side in eManager.

If anyone can help me out, that would be great.

Daren

***Bygcland*** · 07-02-2009

You will have to set the dial 9 to access the OLG for the point to point and then set another 9 to access the PRI at the other location. Once you have done that, the call should be able to go thru. It is easier done than said..

blkphtm · 07-02-2009

So right now we have 4 OLG setup. 2 say Analog, and the other 2 say ISDN.

Currently the 9, (at the site that will be loosing the PRI) is set to "LCR - to place outgoing call using LCR".

So I would just change that to use 1 of the 4 OLG, which ever one is correct, is that what you are saying? OLG 3 in our case is setup as a TIE/E&M, am I correct on this?

Am I able to test this on just one extension, so if I went to station assignments, CO Line or OLG Number?

***Bygcland*** · 07-02-2009

best way to test would be to make a network node access code in the features and have it utilize which ever OLG is the one for the TIE circuit. You should be able to dial that access code and then 9 and the number you want to dial and see if it goes out.

blkphtm · 07-08-2009

Setting the 9 to use the OLG that connects building to building, then pressing 9 (code to access LCR on remote site) to access an outside line does not seem to work. Just a buzzing sound.

Dialing the Network Node (12) and then 9, plus the number does seem to work.

How can I get the system to automatically put or dial 12,9, then the number when the user just presses 9, then the number now?

blkphtm · 07-16-2009

We have got this to work. We had to change the OLG to use the TIE line connection instead of the PRI connection, and add Leading digits (Node ID + 9 to access and outside line).

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Routing Outbound Calls to Specific CO Lines	SeaTown1984	Panasonic	2	12-31-2008 10:55 AM
unanswered outbound calls in CDR	mfiinc	Meridian Systems	2	10-27-2008 11:50 AM
Asterisk, Outbound Routing Help	NewbeNeax2000	Asterisk	0	10-05-2005 01:11 AM
moving osn for 911 calls	tmag	Meridian Systems	2	01-03-2003 06:16 PM
ANI display on outbound calls?	mmyers	Meridian Systems	4	12-16-2002 05:06 PM

Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)