opt 11 to avaya - PBX Info :: Your Free PBX, PABX and Telephone Information Resource

TY · 12-04-2003, 07:35 AM

I'm hooking a non PRI t1 from a nortel OPT 11 in house to a Avaya Magic's switch all settings Ive tried calls wil not connect between the two.Don't know if Avaya is problem.Looking for some direction on Avaya or Nortel side.

Thanks
Ty

**Chas2002** · 12-04-2003, 08:57 AM

Ty - Not sure about the Avaya side, but I can offer some pointers on the Meridian....

First - What is the status of your DCH and B-Channels?

Please post the following: Your ADAN and RDB

LD 22
REQ prt
TYPE adan x (Where x is the DCH associated with your T1)

Should get something like this - depending on what type of card

Quote:

ADAN PRIM DCH 0
BDCH 4
CTYP MSDL
GRP 0
DNUM 12
PORT 1
DES PRIMARYDCHAN
USR PRI - could be BRI
DCHL 8
OTBF 32
PARM RS422 DTE
DRAT 64KC
CLOK EXT
IFC NI2
ISDN_MCNT 300
CLID OPT0
CO_TYPE ATT
SIDE USR
CNEG 1
RLS ID 1
RCAP ND2 COLP
PRI INTERFACE ID
009 2
010 3
011 4
091 5
082 6
083 7
T310 120
T200 3
T203 10
N200 3
N201 260
K 7

Second - Some notes about the Meridian and T1 interoperability ---

1. Make sure you have one side set to User and the other set to Network
2. Once the T1 Layer 1 is up and active, layer 2 will intialize.
3. When Layer 2 is active, each side will send framing info (Acknowledgements and Receiver Ready)

NEXT

Print your RDB and post:
LD 21
PRT RDB x (Where x is your DCH)

Should get something like this.....

Quote:

TYPE RDB
CUST 00
ROUT 0
DES LOCAL
TKTP DID
SAT NO
RCLS EXT
DTRK YES
DGTP PRI
ISDN YES
MODE PRA
IFC NI2
CBCR NO
SBN NO
NCNA YES
NCRD NO
CHTY BCH
CPFXS YES
BCOT 0
INTC NO
DSEL VOD
PTYP PRI
AUTO NO
DNIS NO
ICOG IAO
RANX NO
SRCH LIN
TRMB YES
STEP
ACOD 8000
TCPP NO
PII NO
TARG 01
CLEN 1
BILN NO
OABS
INST
IDC YES
DCNO 1 *
NDNO 1
DEXT NO
DNAM YES
ICIS YES
TIMR ICF 384
OGF 384
EOD 13952
NRD 10112
DDL 70
ODT 4096
RGV 640
FLH 510
GRD 896
SFB 3
NBS 2048
NBL 4096
TFD 0
DRNG NO
CDR YES
INC NO
LAST NO
QREC NO
OAL YES
AIA NO

PAGE 002

OAN YES
OPD NO
NATL YES
MUS YES
MRT 44
MR NO
RACD NO
EQAR NO
FRL 0 0
FRL 1 0
FRL 2 0
FRL 3 0
FRL 4 0
FRL 5 0
FRL 6 0
FRL 7 0
TTBL 0
PLEV 2
MCTS YES
ALRM YES
ART 0
SGRP 0
AACR YES
ASID 16
SFNB
USFB
CALB 7 8

Some important info about the RDB...

Set ISDN = YES
Double check your TKTP (most likely should be TIE)
YOUR ICOG setting should be IAO (Incoming and Outgoing)..
If all your B-Channels are IDLE, try this..

1. Change your Maint set to TGAR 0
2. Dial the ACOD of the Route....

This should be a good starting point....
Chas2002

TY · 12-05-2003, 10:00 PM

Thanks,
The t1 is programed as non-PRI right know no Dchannel. Just built as TIE EAM,wink wink. Avaya is set as EAM auto,auto which alows him to dial me but as soon as I dial him his auto,auto setting forces my call to his attn. not to the ext I dial.If he sets to EAM wink wink my call to him waits 20 secs.then re-order.The avaya switch very limited in options.

Quote:

Originally Posted by Chas2002

Ty - Not sure about the Avaya side, but I can offer some pointers on the Meridian....

First - What is the status of your DCH and B-Channels?

Please post the following: Your ADAN and RDB

LD 22
REQ prt
TYPE adan x (Where x is the DCH associated with your T1)

Should get something like this - depending on what type of card

Quote:

ADAN PRIM DCH 0
BDCH 4
CTYP MSDL
GRP 0
DNUM 12
PORT 1
DES PRIMARYDCHAN
USR PRI - could be BRI
DCHL 8
OTBF 32
PARM RS422 DTE
DRAT 64KC
CLOK EXT
IFC NI2
ISDN_MCNT 300
CLID OPT0
CO_TYPE ATT
SIDE USR
CNEG 1
RLS ID 1
RCAP ND2 COLP
PRI INTERFACE ID
009 2
010 3
011 4
091 5
082 6
083 7
T310 120
T200 3
T203 10
N200 3
N201 260
K 7

Second - Some notes about the Meridian and T1 interoperability ---

1. Make sure you have one side set to User and the other set to Network
2. Once the T1 Layer 1 is up and active, layer 2 will intialize.
3. When Layer 2 is active, each side will send framing info (Acknowledgements and Receiver Ready)

NEXT

Print your RDB and post:
LD 21
PRT RDB x (Where x is your DCH)

Should get something like this.....

Quote:

TYPE RDB
CUST 00
ROUT 0
DES LOCAL
TKTP DID
SAT NO
RCLS EXT
DTRK YES
DGTP PRI
ISDN YES
MODE PRA
IFC NI2
CBCR NO
SBN NO
NCNA YES
NCRD NO
CHTY BCH
CPFXS YES
BCOT 0
INTC NO
DSEL VOD
PTYP PRI
AUTO NO
DNIS NO
ICOG IAO
RANX NO
SRCH LIN
TRMB YES
STEP
ACOD 8000
TCPP NO
PII NO
TARG 01
CLEN 1
BILN NO
OABS
INST
IDC YES
DCNO 1 *
NDNO 1
DEXT NO
DNAM YES
ICIS YES
TIMR ICF 384
OGF 384
EOD 13952
NRD 10112
DDL 70
ODT 4096
RGV 640
FLH 510
GRD 896
SFB 3
NBS 2048
NBL 4096
TFD 0
DRNG NO
CDR YES
INC NO
LAST NO
QREC NO
OAL YES
AIA NO

PAGE 002

OAN YES
OPD NO
NATL YES
MUS YES
MRT 44
MR NO
RACD NO
EQAR NO
FRL 0 0
FRL 1 0
FRL 2 0
FRL 3 0
FRL 4 0
FRL 5 0
FRL 6 0
FRL 7 0
TTBL 0
PLEV 2
MCTS YES
ALRM YES
ART 0
SGRP 0
AACR YES
ASID 16
SFNB
USFB
CALB 7 8

Some important info about the RDB...

Set ISDN = YES
Double check your TKTP (most likely should be TIE)
YOUR ICOG setting should be IAO (Incoming and Outgoing)..
If all your B-Channels are IDLE, try this..

1. Change your Maint set to TGAR 0
2. Dial the ACOD of the Route....

This should be a good starting point....
Chas2002

jack · 12-08-2003, 08:46 AM

T,

Post a copy of your RDB and one of the TN's for a trunk.

What is the extension number range that you are dialing?

Jack

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Meridian Opt. 11 and Octel issues. Cant reply to message.	mholden	NORTEL	1	09-26-2006 06:39 PM
Avaya Styles Hybrid Phones	rixride	AVAYA	4	06-15-2006 09:55 PM
Opt 11 CDP Programming Guidance	mrose77	Meridian Systems	4	05-05-2006 06:43 PM
A4400 -B channel choice error	vittogio	ALCATEL	1	05-05-2006 01:05 AM

Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)