KX-TEA308 FWD to CO - PBX Info :: Your Free PBX, PABX and Telephone Information Resource

dan.e · 10-22-2005, 10:19 AM

The setup:-

PBX is KX-TEA308NE, and has a KX-T7730SP PT attached, other devices are all SLT (untill the 7710's get here next week).
CO1 is an analogue line, CO2 is not connected, C03 is an Ericsson F250M bridge to the mobile network.

ARS is set, and working, for all calls to the mobiles go through CO3

I need to be able to set "FWD to CO" so that all incoming calls are routed to a mobile on CO3 automatically.

If I set another extension to "FWD to CO", then it does work if the call is transfered to the extension manually from the 7730. If I enable DISA and have AA set a message to "press 0" - which directs to call to the "FWD to CO" extension, then I get a message from the mobile operator stating the subscriber number doesn't exist, though the number *is* correct (see manual transfer above)

Anyone know what's going on? The manual states that the CO line mode has to be set to manual (unless I misunderstood), but with DISA (which I would prefer for the fax discriminator to work in addition to the menus) enabled is the closest I've come to getting it to work.

Any input is appreciated.

Dan

***sncsnc*** · 10-24-2005, 03:20 PM

dil line one to your dummy ext and see what happens if it works set up lunch mode
for when you want to forward calls out on the cellular network from line one.

dan.e · 10-25-2005, 12:51 PM

Thanks for the suggestion -I've just tried that - I still get the message from the mobile service provider telling me the number doesn't exist.

I think I'm going to have to make one of those wierd serial cables I made up for a TD1232 a couple of years ago and watch whats happening through a hyperterminal session. I was just hoping someone had come across this before and knew it was a case of "add a 0 to the number ARS forwards to", or something similar.

Again, thank you

Dan

***sncsnc*** · 10-25-2005, 01:06 PM

what does you forward out dialing string look like what did you program in when you forwarded
your ext? ( trunk access code + x-xxx-xxx-xxxx you get the picture I know you arei n uk) do you have access to digit grabber or can you listen across line 3 with a buttset to here whats going on?

dan.e · 10-25-2005, 03:35 PM

It's programmed with the Panasonic maintenance console. There is no trunk access code (none needed) and the filter is 6380442 goes to CO group 3 (the mobile network bridge), number of removed digits is 1, added digit is 6 - without that, 050 is always added for some reason I have yet to work out. However, when I changed the CO group to use the second land line, it worked ok, though there did seem to be some extra dialling going on.

Very odd.

BTW, I'm not in the UK, I'm in Spain. What made you think I was in the UK?

Dan

judokah · 11-25-2005, 09:51 AM

Can someone help me to get the price quote for a complete PBX setup for 20 office rooms? (Phoen boxes inclusive)
Thanks

judokah · 11-25-2005, 11:15 AM

Can someone help me to get the price quote for a complete PBX setup for 20 office rooms? (Phoen boxes inclusive)
Thanks

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Fwd To Ext No	shankar	MD 110 SUPPORT	3	06-27-2007 01:08 AM
<ask> Configuring E&M on KX TD 500 and TDA 100	red99	Panasonic	3	06-13-2006 01:37 AM
Phantom FWD to different VM?	John_In_Dakota	Meridian Systems	14	05-19-2006 02:39 PM
Panasonic kx td1232 smdr	AnilSB	Panasonic	9	05-12-2006 06:29 AM

Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)