Programming KX-TEM824 - PBX Info :: Your Free PBX, PABX and Telephone Information Resource
Home | Register |    
 
Forums         |        Articles          |        Blogs         |      Software          |      Portals          |      Resource          |      Wiki      |    White Papers         
 
Go Back   PBX Info :: Your Free PBX, PABX and Telephone Information Resource > PBX SYSTEMS > Panasonic
Reload this Page Programming KX-TEM824
   SEARCH  
     
User Name Password      
Save ?
Panasonic Post Questions and Answers about Panasonic systems and products. i.e.: Telephone Hybrid/PBX Systems KX-T, KX-TA, KX-TD Voice Mail Systems KX-TVS, KX-TVA

Tags: ,


Reply
 
LinkBack Thread Tools Display Modes
Old 03-21-2007, 09:36 AM   #1 (permalink)
naffilk
Junior Member

Activity Longevity
0/20 6/20
Today Posts
0/0 ssssssss2
Location: Bahrain
Rep Power: 0naffilk is an unknown quantity at this point
Gender:
Country:
Send a message via MSN to naffilk Send a message via Yahoo to naffilk Send a message via Skype™ to naffilk
Programming KX-TEM824
Hi,

I am new to PBX programming. I am using KX-TEM824 board.
I tried to receive data from board using a small C#.NET 2.0.

But its not reading any data.
Please tell is there any code to be passed to retrieve data.

I set the connection parameters as follow,
Baud Rate: 9600 bps
Word Length: 8 bits
Parity Bit: None
Stop Bit: 1 bit

Thnx in advance.
naffilk is offline   sendpm.gif Reply With Quote
Old 03-21-2007, 12:56 PM   #2 (permalink)
ShawnC
Junior Member

Activity Longevity
0/20 20/20
Today Posts
0/0 sssssss33
Location: NEW ENGLAND
Rep Power: 7ShawnC is on a distinguished road
Gender:
Country:
Send a message via ICQ to ShawnC
are you pluged into the serial port or the usb?

please update your country in profile.....
Last edited by ShawnC; 03-21-2007 at 12:59 PM.
ShawnC is offline   sendpm.gif Reply With Quote
Old 03-22-2007, 08:10 AM   #3 (permalink)
naffilk
Junior Member

Activity Longevity
0/20 6/20
Today Posts
0/0 ssssssss2
Location: Bahrain
Rep Power: 0naffilk is an unknown quantity at this point
Gender:
Country:
Send a message via MSN to naffilk Send a message via Yahoo to naffilk Send a message via Skype™ to naffilk
Yes its pluged into the serial port.
naffilk is offline   sendpm.gif Reply With Quote
Old 03-22-2007, 02:20 PM   #4 (permalink)
rivet
Senior Member

Activity Longevity
1/20 8/20
Today Posts
0/0 ssssss127
Location: Dublin
Rep Power: 3rivet is on a distinguished road
Gender:
Country:
did you switch on the printer in the system software

peter (www.vpi.ie)
rivet is offline   sendpm.gif Reply With Quote
Old 04-18-2007, 03:50 AM   #5 (permalink)
tongdai.com.vn
Junior Member

Activity Longevity
0/20 7/20
Today Posts
0/0 sssssss25
Rep Power: 0tongdai.com.vn is an unknown quantity at this point
Country:
Post
you can use the windows hyperterminal to test to see if SMDR is
being sent...
Last edited by sncsnc; 05-20-2007 at 08:47 PM. Reason: Grammer
tongdai.com.vn is offline   sendpm.gif Reply With Quote
Old 05-10-2007, 03:25 AM   #6 (permalink)
gjon.ndreca
Junior Member

Activity Longevity
0/20 5/20
Today Posts
0/0 sssssss10
Location: Kosovo Un administration
Rep Power: 0gjon.ndreca is an unknown quantity at this point
Gender:
Country:
If you just connect TEM-824 with the PC it will automatically send data to your PC, you don't need to configure the switchboard, just make sure that you have the correct cable, and correct pin in the connector is conected.
gjon.ndreca is offline   sendpm.gif Reply With Quote
Old 05-20-2007, 01:50 PM   #7 (permalink)
phull_iqbal
Junior Member

Activity Longevity
0/20 9/20
Today Posts
0/0 ssssss221
Location: UAE (United Arab Emirates)
Rep Power: 3phull_iqbal is an unknown quantity at this point
Gender:
Country:
Check the cable connection
Dear
I am 100% sure that is cabling fault. Please make the proper connection. Check the cable with multimeter before using it. Please make the following connection

PBX Side PC Side
2 3
3 2
4 6
5 5
6 4
7 8
8 7


It should work perfectly. Check all the setting like baud rate and other setting. it should be default.
Thanks
phull_iqbal is offline   sendpm.gif Reply With Quote
Reply

« Previous Thread | Next Thread »


Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
Thread Tools
Display Modes
Linear Mode Linear Mode

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On

Similar Threads
Thread Thread Starter Forum Replies Last Post
KX-TEM824 Setup siw Panasonic 17 04-16-2008 05:28 AM
KX-TEM824 outside call CO order lynx Panasonic 2 12-11-2006 04:32 PM
SMDR on KX-TEM824 fredyan Panasonic 8 09-05-2006 07:32 PM
DMI / RLI Programming Chas2002 Meridian Systems 2 07-27-2004 01:28 PM
Programming dan BCM and Norstar 4 09-08-2003 01:49 PM


All times are GMT -5. The time now is 09:53 AM.

Tags   |   Advertise    |    Media Partners   |    Admin   |   About us   |   Contact Us   |   RSS   

Powered by vBulletin® Version 3.7.3
Copyright ©2000 - 2008, Jelsoft Enterprises Ltd.
Search Engine Friendly URLs by vBSEO 3.0.0
Copyright PBXINFO LLC 2006