 | |
| |||||||||||||||
| |||||||||||||||
| NORTEL PBXINFO is internet authority resource center for Nortel and Avaya gear. |
| Tags: isdn qsig |
 |
| | LinkBack | Thread Tools | Display Modes |
| | |
| |||||||||||||||
| |||||||||||||||
| NORTEL PBXINFO is internet authority resource center for Nortel and Avaya gear. |
| Tags: isdn qsig |
|
| | LinkBack | Thread Tools | Display Modes |
 June 13th, 2007 | #1 (permalink) | ||||||||
| Senior Member   TomasSouth has no status.
Rep Power: 8   | ISDN-QSIG to Cisco Any one out there had configured an E1 QSIG going to Cisco Call Manager successfully using only IFC=ESIG or IFC=ISIG? I had configured it that way but in vain. Maybe something I miss out of the normal way of programming in LD 17, 16, or 14. I am using NT5D97 and NTBK51, X21 R4.5. Only using Enhanced Business, not required to order Advanced Network, since it was described in Nortel docs it could happen, unfortunately it doesn't mention the exact way of programming it.  Thanks. | ||||||||
 |   |
| July 4th, 2007 | #2 (permalink) | ||||||||
| Senior Member TomasSouth has no status.
Rep Power: 8 | Thanks, but this case is close. There is no special programming, just do the normal procedure of doing the ESIG way, and Enhanced Business is enough. Just misunderstanding with the TX and RX happened.  It is really advisable to heed what the alarms says. | ||||||||
| | |
| January 28th, 2010 | #3 (permalink) | ||||||||
| Junior Member
Location: India Rep Power: 5 Gender:  Country:   | Hi Does it work with ISIG/ESIG without GF package ??? I did a integration yesterday and having speech path issue intermittent.(no speechpath) Can you help to confirm or post the codes ! thanks Below is my d channel config! do i miss anything ?? ADAN DCH 60 CTYP MSDL MG_CARD 004 0 03 PORT 1 DES VSAT_TIE_60 USR PRI DCHL 60 OTBF 32 PARM RS422 DTE DRAT 64KC CLOK EXT IFC ISIG ISDN_MCNT 300 CLID OPT0 CO_TYPE STD SIDE USR CNEG 1 RLS ID ** QCHID NO RCAP COLP MBGA NO OVLR NO OVLS NO T310 120 T200 3 T203 10 N200 3 N201 260 K 7 | ||||||||
| | |
|
| Currently Active Users Viewing This Thread: 1 (0 members and 1 guests) | |
| Thread Tools | |
| Display Modes | |
| |
 Similar Threads | ||||
| Thread | Thread Starter | Forum | Replies | Last Post |
| Qsig connection Meridian to Cisco Calmanager | nortelzo@gmail.com | Meridian Systems | 4 | April 4th, 2007 09:07 AM |
| Configure qsig m110 bc 10 between cisco call manager | gmma | MD 110 SUPPORT | 2 | October 27th, 2006 03:55 PM |
| C11 and Cisco router via T1 isdn connect help | wchpikus | Meridian Systems | 16 | May 2nd, 2005 09:12 PM |
| QSIG to Cisco Call Manager | mark@stjoes | Meridian Systems | 2 | February 10th, 2005 12:29 PM |
| Ties to Cisco using QSIG | mark@stjoes | Meridian Systems | 4 | September 1st, 2004 11:57 PM |
Linear Mode
