Home         |        Forums         |        Portals          |           Login               |     Register              
 
Go Back   VoIP / PBX Info Forum for Avaya / Nortel, Cisco, ShoreTel, Panasonic and other manufactuers Tech Tips Community > PBX / IP PBX FORUMS > NORTEL
Reload this Page PBX Lockout
   SEARCH  
     
User Name Password      
Save ?
NORTEL PBXINFO is internet authority resource center for Nortel and Avaya gear.

Tags: ,


Free Call Accounting Quotes   PBX Programming Software  Nortel Software  Avaya Products  Cisco Call Accounting

Reply
 
LinkBack Thread Tools Display Modes
Old December 7th, 2006   #1 (permalink)
Junior Member

Activity Longevity
0/20 9/20
Today Posts
0/0 ssssssss4
Rep Power: 0dmedellin is a newbie
Country:
Unhappy PBX Lockout
I have an Opt 61C rel 17.76 w/ meridian mail ver 8.0

The situation here is that the tape backup drive has gone out and because of this. We are unable to execute any load commands. We can connect and see that the terminal communicates. However, whenever we login and type any load all we get is:

IOD101 02
OVL005

The tape drive replacement is on it's way but, I still would need to get into the PBX to disable the drive unit before I can replace it. Does anyone know how to backdoor into this? or force it to accept LD commands??
Last edited by dmedellin; December 7th, 2006 at 04:13 PM.
dmedellin is offline   sendpm.gif Reply With Quote
Old December 7th, 2006   #2 (permalink)
Moderator
 
rixride's Avatar
rixride is replying to forum games...

Activity Longevity
0/20 20/20
Today Posts
0/0 sssss3093
Location: Dallas, Texas
Rep Power: 21rixride has much to be proud ofrixride has much to be proud ofrixride has much to be proud ofrixride has much to be proud ofrixride has much to be proud ofrixride has much to be proud ofrixride has much to be proud ofrixride has much to be proud of
Gender:
Country:
 
hmm. You have tried different TTY ports? Do you have multi-user log in enabled?
rixride is offline   sendpm.gif Reply With Quote
Old December 8th, 2006   #3 (permalink)
Junior Member

Activity Longevity
1/20 10/20
Today Posts
0/0 sssssss41
Rep Power: 0rajblr1 is a newbie
Country:
JUST CHECK the staus of the TTY port on overlay 37 , if it is disabled you need to enable that .
rajblr1 is offline   sendpm.gif Reply With Quote
Old December 8th, 2006   #4 (permalink)
Junior Member

Activity Longevity
0/20 9/20
Today Posts
0/0 ssssssss4
Rep Power: 0dmedellin is a newbie
Country:
The problem lies in that I cannot enable or disable anything because after logging in, anything typed in is ignored and i'm returned to the carriage prompt >
No settings have changed nor has any hardware been added. In order to perform any functions I would have to be "in the system". Hence, my dilema, how do I force it to accept a LD when it doesn't acknowledge my input because of the damaged tape drive. Worse part is that I now have the replacement part but the PBX won't let me disable anything and repeats error
IOD101 02
OVL005
>


The following is an example of my results:
IOD101 02
OVL005
>TTAD
OVL013
>****
>LD 10
IOD101 02
OVL005
>PRT
OVL013
>
TIM0000 13:27 7/12/2006 CPU 1
LD 35
IOD101 02
OVL005
>STAT
ENBL
TRACK 1 DSBL
>****
>
DTC001
TIM0000 13:42 7/12/2006 CPU 1
DTC001
DTC001
OVL020 LD 37
IOD101 02
OVL005
>
TIM0000 14:18 7/12/2006 CPU 1
dmedellin is offline   sendpm.gif Reply With Quote
Old December 8th, 2006   #5 (permalink)
Junior Member
 
dannoWI's Avatar
dannoWI is stupified

Activity Longevity
0/20 9/20
Today Posts
0/0 sssssss63
Location: Monticello (not the famous one)
Rep Power: 0dannoWI is a newbie
Gender:
Country:
Do you have a maintenance telephone setup?

You may be able to login to that and disable the tape unit to replace it.
Because the system can't access the tape and the loads you need probably are not cached you will not get in via tty.
dannoWI is offline   sendpm.gif Reply With Quote
Old December 8th, 2006   #6 (permalink)
Junior Member

Activity Longevity
0/20 9/20
Today Posts
0/0 ssssssss4
Rep Power: 0dmedellin is a newbie
Country:
tried that, the maintenance telephone is setup and, punched in commands display on terminal. However the same limitations are emulated.

I do appreciate the feedback though. Suggestions are still requested.
dmedellin is offline   sendpm.gif Reply With Quote
Old December 8th, 2006   #7 (permalink)
Junior Member
 
dannoWI's Avatar
dannoWI is stupified

Activity Longevity
0/20 9/20
Today Posts
0/0 sssssss63
Location: Monticello (not the famous one)
Rep Power: 0dannoWI is a newbie
Gender:
Country:
If you type-
>DIST
>ENLT

does that help at all?

When you do >DIST do any red lights come on?
dannoWI is offline   sendpm.gif Reply With Quote
Old December 15th, 2006   #8 (permalink)
Junior Member

Activity Longevity
0/20 9/20
Today Posts
0/0 sssssss37
Location: VA
Rep Power: 4DenWalters is a newbie
Gender:
Country:
The problem with the processors with tape drives and the older software release is that the the Mainenance and Adminstrative Loads are actually stored on your tape drive. That there was not enough cache memory with those processors to support repetative commmands. I would say that that system is well past due for an upgrade.
DenWalters is offline   sendpm.gif Reply With Quote
Old December 15th, 2006   #9 (permalink)
Junior Member

Activity Longevity
0/20 9/20
Today Posts
0/0 ssssssss4
Rep Power: 0dmedellin is a newbie
Country:
informative, yet unhelpful in resolving problem. It is acknowledged that the system is due for an upgrade. And slated for next fiscal budget.

*Update. Issue has been resolved, using maintenance phone vendor was able to restore PBX connection.
Thank you all for your help and suggestions.
dmedellin is offline   sendpm.gif Reply With Quote
Old June 1st, 2007   #10 (permalink)
Junior Member
 
subby's Avatar
subby has no status.

Activity Longevity
0/20 8/20
Today Posts
0/0 ssssssss1
Location: San Antonio
Rep Power: 0subby is a newbie
Gender:
Country:
You are very welcome dmedellin.
subby is offline   sendpm.gif Reply With Quote
Reply

« Previous Thread | Next Thread »

Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
Thread Tools
Display Modes
Linear Mode Linear Mode

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On

Similar Threads
Thread Thread Starter Forum Replies Last Post
Busy Signal in PBX emaloney Inter-Tel 10 December 20th, 2006 08:31 AM
How to connect kx-ta308 PBX to kx-tva50 VPS asohnsa Panasonic 3 June 27th, 2006 11:23 AM
Looking for PBX Design Engineer Newton Other 0 April 24th, 2006 08:05 PM


All times are GMT -4. The time now is 02:43 AM.

Contact Us - PBX Info Forum | Telephony Resource Tech Tips Community for Avaya, Nortel, Cisco, Panasonic, ShoreTel, Asterisk and more... - Archive - Top

Powered by vBulletin® Version 3.7.3
Copyright ©2000 - 2010, Jelsoft Enterprises Ltd.
Search Engine Friendly URLs by vBSEO 3.2.0
Copyright (c) www.pbxinfo.com - PBX Info | Free PBX, PABX, IP PBX, VOIP and Telephone Information Resource Forum - Avaya / Nortel, Cisco, Panasonic, Mitel, ShoreTel, more...