| |||||||||
 |
| ||||||||
| |||||||||||||||
| |||||||||||||||
| NEC Ask Questions and Find Answers: |
| Tags: moves, station |
  |
| | LinkBack | Thread Tools | Display Modes |
| |||||||||
|
| ||||||||
| |||||||||||||||
| |||||||||||||||
| NEC Ask Questions and Find Answers: |
| Tags: moves, station |
| |
| | LinkBack | Thread Tools | Display Modes |
 02-21-2007, 12:43 PM | #1 (permalink) |
| Junior Member | Station Moves Our company has about 80 people switching cubes tomorrow and we're looking for a better way to move stations. Our current method involves visiting the punch-down block where we occassionally break more things than we fix. We've got a good listup of the station and lens data and logic is telling me we should be able to assign a station to another lens without having to delete the station data first. Can anyone share some insight about how to easily move a station if you know the lens you are moving from and the lens you want to move to? We're using a NEAX 2400 IMX and using the R18 MAT console. |
 |   |
| 02-21-2007, 01:46 PM | #2 (permalink) |
| Moderator | Hello billmcl The easy way "but NOT the best" is to use your PC and swap numbers and lens. But I would strongly recommend the best solution which you do it once and for ever: have your pbx cables terminated on one termainal block, and your home cables termainated on another then run jumpers between the two blocks, in so doing you will be playing with the jumpers whenever ther is a need to move any one from one office to another. |
| | |
| 02-21-2007, 01:54 PM | #3 (permalink) |
| Junior Member | Yes, that's the way we do it now but end up bumping other cables during the process causing a disruption in service. The way we're trying to do it would permanently assign the lens to the office, cube, or whatever and only the station data would change. |
| | |
| 02-21-2007, 10:14 PM | #4 (permalink) |
| Moderator | OK, you are favoring the "easy" method. Please keep in mind that in case you are moving Dterms numbers, if any, you have to reassign the key data for each dterm as well, cause the key data are assigned to NUMBERS and not to LENS,and so it does not move out when swaping dterm number. Last edited by AbuSuhail : 02-21-2007 at 10:16 PM. |
| | |
| 02-23-2007, 08:26 AM | #5 (permalink) |
| Junior Member  | Another way you could do it is to move the terminations from blocks to a patch panel. Put your terminations for your house cable and phone switch onto patch panels, then all you have to do is move patch cords (i.e. cat5e) to swap stations and not have to worry about punch downs. I know this isn't a quick fix and will cost a little bit of money, but if you move extensions a lot it might be the easiest way. It is also relative to how many phones you have terminated on your system and the corresponding space for hanging patch panels in your switch room. Good luck. |
| | |
| |
| Currently Active Users Viewing This Thread: 1 (0 members and 1 guests) | |
| Thread Tools | |
| Display Modes | |
| |
 Similar Threads | ||||
| Thread | Thread Starter | Forum | Replies | Last Post |
| Ext moves and ACDN | cybervex | Meridian Systems | 7 | 02-09-2007 09:24 AM |
| station to station calling restriction | wilabkr3i_zrhedd | Electra Elite | 0 | 02-01-2007 07:57 PM |
| Tracking Moves/Adds/Changes | marsh171 | Meridian Systems | 1 | 01-11-2006 12:25 PM |
| Moves, Adds & changes | matrix9 | BCM and Norstar | 1 | 11-23-2003 08:11 PM |
| How to handle moves? | dkraut | Technology Chat | 6 | 05-14-2003 07:30 PM |
Linear Mode
