bobcheese

Ok this would be a little long winded to guide you through via messages. Do you have access to any manuals? If so the feature that you are looking for is called 'remote access to system'

hope this helps

Ethan_Hunt

yeah i do...how do i proceed?

R4+Z

Sounds like mission impossible to me.

R4+Z

An extract from the Feature Programming Manual. Hope my reformatting for this forum hasn't made it hard to use.



REMOTE ACCESS TO SYSTEM
PROGRAMMING
DESCRIPTION DATA

CM08
Specify the processor for checking the ID code
for Remote Access to System.
(1) 217
(2) 0 : MP card
1 : OAI (ACF)


Assign the ring cadence on a Remote Access to
System.
(1) 180
(2) 0 : As per CM08>392 Pattern2
1 : As per CM35 Y=33


CM2A
Assign the ID Code Development number for
Remote Access to System.
• Y=A0
(1) 2
(2) 0-9: ID Code Development No. 00-09
NOTE: CM2A Y=00-09 is determined by this data.

Assign the ID Code for Remote Access to System.
• Y=00-09 ID Code Development No. 00-09
(1) X-XX...XX: ID Code for Remote Access to
System (Maximum 16 digits)
(2) 0000-2999: ID Code Pattern No.



Assign the desired Trunk Restriction Class for
each ID Code Pattern number.
• Y=11
(1) 0000-2999: ID Code Pattern No.
(2) 1 : Unrestricted (RCA)
2 : Non-Restricted-1 (RCB)
3 : Non-Restricted-2 (RCC)
4 : Semi-Restricted-1 (RCD)
5 : Semi-Restricted-2 (RCE)
6 : Restricted-1 (RCF)
7 : Restricted-2 (RCG)
8 : Fully-Restricted (RCH)


Assign the desired Service Restriction Class A
to each ID Code Pattern number. The features
available in each class are assigned by CM15.
• Y=12
(1) 0000-2999: ID Code Pattern No.
(2) 00-15 : Service Restriction Class A



Assign the desired Service Restriction Class B
to each ID Code Pattern number. The features
available in each class are assigned by CM15.
• Y=13
(1) 0000-2999: ID Code Pattern No.
(2) 00-15 : Service Restriction Class B


Assign the desired Service Restriction Class C
to each ID Code. The features available in each
class are assigned by CM15.
• Y=14
(1) 0000-2999: ID Code Pattern No.
(2) 00-15 : Service Restriction Class C

Assign the purpose of ID Code.
• Y=10
(1) 0000-2999: ID Code Pattern No.
(2) 0 : Validate the ID Code entered from
stations and trunks
2 : Validate the ID Code entered from
trunks
3 : Invalidate the ID Code entered from
stations and trunks


CM30
Assign terminating system in Day Mode,
Night Mode, Mode A and Mode B for incoming
C.O. Calls to required trunks.
• Y=02 Day Mode
• Y=03 Night Mode
• Y=40 Mode A
• Y=41 Mode B
(1) 000-255: Trunk No.
(2) 16: Remote Access to System


Specify the handling of busy/not available Remote
Access to System destination in Day or
Night Mode when calling an internal station.
• Y=30 Handling of busy/not available
Remote Access to System
destination in Day Mode
• Y=31 Handling of busy/not available
Remote Access to System
destination in Night Mode
(1) 000-255: Trunk No.
(2) 00 : C.O. Line release
01 : Forwarded to TAS
03 : Forwarded to Attendant Console
04 : Forwarded to DIT station assigned
by CM30 Y=04, 05
06 : DT connection for redial
08 : C.O. line release
15 : C.O. line release

CM35
Assign the release signal condition to a incoming
trunk route assigned by CM30 Y=00.
• Y=05
(1) 00-63: Trunk Route No.
(2) 1 : Release signal arrives


CM36
Specify the combination of Trunk Routes allowing
the Trunk-to-Trunk Connection.
• Y=0
(1) XX ZZ
XX: 00-63: Incoming Trunk Route
ZZ : 00-63: Outgoing Trunk Route
(2) 0 : Allowed
1 : Restricted


CM42
Specify the maximum number of digits for Remote
Access to System.
(1) 13
(2) 01-16: 1 digit-16 digits
NONE : 16 digits

NOTE: Approximately 3000 Remote Access to System codes including Authorization Codes and Forced Account Codes can be defined.

Ethan_Hunt

thanks man you're such a big help....