dryaquaman

(1) program your "Trunk Service Assignment " form. Set set the day/n1/n2 to ring where ever you want it to go.
(2) program the trunk in the "analog trunk assignment" form. Be sure to give it the Trunk Service number you assigned in step 1 above.
(3) plug line in to 3300.
(4) test.

Dry_aquaman

3300CXIuser

could u please give more details ?
waht numbers should i put in the fields ?

acejavelin

The numbers you put in these fields could vary greatly and are dependant on your particular setup and configuration. This is the basics of what you need:
------------------
CO Trunk Circuit Descriptor Assignment (add a new one, major things noted)

Number: 1
Line Start Type: Loop <= For loop start trunks
Post Call Metering: No
Guard Timer: 1500
Calling Party Disconnect: No
Dictation Trunk: No
Ignore Far End Disconnect: No
Disconnect Timer: 500
Ignore Far End Reversal During Seizure: Yes
Ringing Expected: Yes <= Make sure to set this
Seize Timer: 10
Address Signalling: DTMF
Fake Answer Supervision After Outpulsing: Yes
Ignore Answer Supervision: Yes
Release Supervision Expected: Yes
Audio Inhibit Until Answer Supervision: Yes
High Loss Option: No
Balance Network Setting: National Complex
Trunk Category: Short
Perform seize test on out-of-service trunks: Yes
Ground Condition During Busy Out: Removed
First Meter Pulse Is Answer: No
Minimum Ring Detection Timer: 200
Drop Digit Rcvr for Outgoing Audio Before Ans Sup: No
Flash Timer: 300
Call Clearing Signal: Disconnect
AC Impedance: National
CLASS Trunk: Yes <= Yes if CID is provided by telco
Milliwatt Tone:
Silence Tone:
-------------
Trunk Service Assignment (pick an unused number):

Trunk Service Number: 1
Release Link Trunk: No
Class of Service: 7 (Will vary depending on setup)
Class of Restriction: 1 (Will vary depending on setup)
Baud Rate: 300
Intercept Number: 1
Non-dial In Trunks Answer Point - Day: 250 <= Where calls ring in to Day mode
Non-dial In Trunks Answer Point - Night 1: 250 <= Where calls ring in to Night 1 mode
Non-dial In Trunks Answer Point - Night 2: 275 <= Where calls ring in to Night 2 mode
Dial In Trunks Incoming Digit Modification - Absorb: (leave blank for LS trunks)
Dial In Trunks Incoming Digit Modification - Insert: (leave blank for LS trunks)
Trunk Label: <name of trunk, optional>
--------------------
Analog Trunk Assignment (select appropriate one that you will connect line to)

Cabinet: 2
Shelf: 1
Slot: 1
Circuit: 5
Card Type: Hybrid 4 ONS 6 LS
Trunk Number: 1 <= Must be unique
Trunk Service Number: 1 <= From Trunk Service Assignment above
DTS Service Number:
Circuit Descriptor Number: 1 <= From Circuit Descriptor assignment above
Interconnect Number: 1
Tenant Number: 1
Balance Network Setting: National Complex
Trunk Category: Short
Auto Select: No
Milliwatt Trunk Number:
CO Telephone Number:
---------------------

This should be all you need to program a LS trunk in your system, hope it helps. This is generally something a vendor should do if you are not familiar with it or it has never been setup before in your switch.

This depends largely on the customer, but generally speaking, customers make simple moves and changes that are set or group based or do not require hardware changes such as system speed dials, hunt group members, button mapping, adding/swapping IP extensions, etc. If hardware changes are involved such as connecting new trunks that were not defined previously and the administrator is not familiar with the programming involved, I recommending getting a technician from a authorized vendor involved to do this work for you.

__________________
Telephony users cannot gain anything without first giving something in return. To obtain a useful feature, a feature of equal value must be lost.

This is Telephony’s First Law of Equivalent Exchange.