 | |
| |||||||||||||||
| |||||||||||||||
| Meridian Systems Welcome to the Nortel Meridian Forums Including Meridian Options 11-81C CS1000M Meridian Mail Call Pilot Companion and Sucession Hospitality OTM MAT MICB RAN NetGateway ..., and all other Applications |
| Tags: clid, pri |
 |
| | LinkBack | Thread Tools | Display Modes |
 August 18th, 2004 | #1 (permalink) | ||||||||
| Guest
| I say not HOT enough! I have a PRI installed and I'm not getting CLID info showing on my phones when someone is calling in. All I see is the trunking information. The Carrier says I have CLID on this line. What do I have to set in the PBX to turn this feature on? Can anyone help me please? | ||||||||
 |
| August 18th, 2004 | #3 (permalink) | ||||||||
| Guest
| Ahhh. ok, there is a Pri DCH and A Backup DCH. both in the CFN don't have a CLID entry. Now, when I go to change the DCH in 17 do I have to dissable both DCH's and all the loops in the route? Or just both DCH's? Cause when I DSBL 1 of the DCH's and try to make the change I get the following: SCH5578: Logical application must be disabled. | ||||||||
| |
| August 18th, 2004 | #4 (permalink) | |||||||||
| Moderator    gei_spot is going phishing
Location: Somewhere in this vast universe on a little rock that looks like a grape. Rep Power: 13  Gender:  Country:  | Quote:
__________________  I'm a member of the "PbxInfo Band" | |||||||||
 |  |
| August 19th, 2004 | #5 (permalink) | ||||||||
| Guest
| 11c compact I disabled both DCH's and all trunks. Went to make the change, but never got the CLID prompt. Here is my buildout for the DCH. ADAN PRIM DCH 42 BDCH 43 CTYP MSDL GRP 1 DNUM 10 PORT 2 DES ATTDIRECT USR PRI DCHL 42 OTBF 32 PARM RS422 DTE DRAT 64KC CLOK EXT IFC ESS4 SIDE USR CNEG 1 RLS ID ** RCAP ND2 MBGA NO OVLR NO OVLS NO PRI INTERFACE ID 034 2 035 3 050 4 051 5 T200 3 T203 10 N200 3 N201 260 Any ideas? | ||||||||
| |
| August 19th, 2004 | #7 (permalink) | ||||||||
| Junior Member
Rep Power: 8 Country:  | Can anyone tell me what some of the PDT commands do? Have you gone into LD 96 and done monitored you DCH messages to see what you are actually receiving? I would suggest to do so before you make many changes. LD 96 >ENL MSGI x (where x=dch to monitor) If this is a real busy trunk route I suggest waiting for a slow traffic period. Also the CLID prompt in the CFN is for CLID in CDR records. | ||||||||
| | |
| August 19th, 2004 | #9 (permalink) | ||||||||
| Guest
| This is what I see when I watch the MSGI on the Primary DCH. DCH 42 IMSG SETUP REF 000080A1 CH 34 22 TOD 10:46:54 CALLED #:1628 NUM PLAN: E164/NATIONAL (NPA) DCH 42 IMSG SETUP REF 000080A2 CH 43 19 TOD 10  22CALLED #:1231 NUM PLAN: E164/NATIONAL (NPA) I'm not seeing the number's coming in. Does this mean I'm not set to recieve them? Or that the provider isn't sending them? | ||||||||
| |
|
| Currently Active Users Viewing This Thread: 1 (0 members and 1 guests) | |
| Thread Tools | |
| Display Modes | |
| |
 Similar Threads | ||||
| Thread | Thread Starter | Forum | Replies | Last Post |
| Change CLID | Icy | Meridian Systems | 6 | November 4th, 2003 04:27 AM |
| CLID for different number range | absinthium | Meridian Systems | 3 | August 28th, 2003 10:02 PM |
| clid issue | dixiedogger | Meridian Systems | 3 | July 7th, 2003 12:07 PM |
| CLID Issue on Tandem out Calling | keith1 | Meridian Systems | 1 | June 25th, 2003 11:45 PM |
| CLID on wireless phones | twscrb | Meridian Systems | 6 | April 29th, 2003 09:51 AM |
Linear Mode
