| |||||||||
![]() | | ||||||||
| |||||||||||||||
| |||||||||||||||
| Meridian Systems Welcome to the Nortel Meridian Forums Including Meridian Options 11-81C CS1000M Meridian Mail Call Pilot Companion and Sucession Hospitality OTM MAT MICB RAN NetGateway ..., and all other Applications |
| Tags: configure, itg, wont |
![]() |
| | LinkBack | Thread Tools | Display Modes |
| | #1 (permalink) | ||||||||
| Junior Member ![]()
Location: Jacksonville, AR Rep Power: 6 ![]() | DNB parsing tools?? I'm having problems getting my ITG 2.1 card to configure thru OTM 2.0. I configure the card for the VoIP node to be 172.20.40.2, with a TN of 004-0-12, but everytime I send the configuration to the card and do a reset, it doesn't configure. The VoIP node allways shows up with an IP address of 0.0.0.0. I made sure the card was disable before sending the configuration to the card. My configure is as follows: ITG 2.1 doesn't require a dongle, correct? lnPci does not even show up at all! ROUTE NET TABLE destination gateway flags Refcnt Use Interface ---------------------------------------------------------------------------- 0.0.0.0 0.0.0.0 1 0 0 lnIsa0 0.0.0.0 137.135.128.1 3 0 0 lnIsa0 137.135.128.0 137.135.128.250 101 0 0 lnIsa0 137.135.128.0 137.135.128.250 101 0 0 lnIsa0 ---------------------------------------------------------------------------- ROUTE HOST TABLE destination gateway flags Refcnt Use Interface ---------------------------------------------------------------------------- 127.0.0.1 127.0.0.1 5 0 0 lo0 ---------------------------------------------------------------------------- value = 77 = 0x4d = 'M' VoIP Node: 172.20.40.2 VoIP Gateway: 172.20.40.1 Netmask: 255.255.255.0 Management IP: 137.135.128.250 Management Gateway: 137.135.128.1 Meridian Primary IP: 137.135.128.253 Management Netmask: 255.255.255.0 FYI: Index : 0 Type : EXUT Role : Leader Node : 0 Leader IP : 0.0.0.0 Card IP : 137.135.128.250 Card TN : 0 0 0 Card State : UNEQ Uptime : 3120 days, 8 hours, 55 mins, 12 secs (269600112 secs) Codecs : G711Ulaw(default), G711Alaw, G729AB lnPci stat : 100 Mbps (Carrier OK) Here is the output of the ITG Card: ITG Firmware Rls 5.0 8051XA Firmware Version 9.1 (Pentium) 14 March 2001 (C) Nortel Networks Inc., 1996-2001 32K External RAM detected All FPGAs are configured No dongle detected 8K DPRAM detected Bank 0 Checksum - 9948H Suspend Power Signals O.K. üPentium(R) II Processor. L2 Cache Enabled Jumping to vxWorks... ZYXWVUR Memory Test Completed OK BIOS ROM Pentium (PC BIOS) Version 1.2 Copyright: Nortel Inc., 1999-2000 Memory Config: 04040404 Memory Size: 0x02000000 PCI Chipset Init Done Enter jkl to force boot from BIOS ROM 00000015 Flash Size: 0x00400000 11 0xF8500000 00 0xF9800000 11 0xF9900000 11 0xF9A00000 11 0xF9B00000 Cookie array value: 0x11111100 Checksum Validation at Bank Address: 0xF9800000 Checksum in ROM = 845131E8 Length of bank = 00147540 Calculated Checksum = 845131E8 Checksum array value: 0x11111100 Loading code from address: F9800010 Cookie Address : 0xF9800010 Cookie Value : 0x90909090 Jumping to VxWorks at 0x00E00000 EIP = 0x00E0011E Jumping to romStart at 0x00E00300 Uncompress Passed OK sysHwInit start sysHwInit Disable PIIX4E IDE sysHwInit Enable PCI Bus Arbitration limit to PCI Clocks:00000040 sysHwInit Enable PIIX Passive Release of PHOLD sysHwInit: sysIntInitPIC - Interrupt Controller sysHwInit: PIIX4E Interrupt steering setup sysHwInit: PCMCIA device Misc Control 3 setup sysHwInit: sysSerialHWInit Memory Configuration: Bank 0: 32MB sysMemTop: configuring GDT with RAM information sysHwInit2: Connecting PIT0 (sysClk) Interrupt Vector sysHwInit2: Connecting RTC (sysAuxClk) Interrupt Vector sysHwInit2: Calling sysSerialHwInit2 sysHwInit2: Connecting stray interrupt handler sysHwInit2: Connect task-level exception handler Enter xxx to force boot from BIOS ROM Setting tLogTask priority to 255 Found device : Cirrus CL-PD672x /C: drive (Flash Chip) is TrueFFS formatted /C: drive (Flash Chip) is an available dosFs file system ipMethodInit, gIPMethod = 2 IP Data in NVRAM Valid, Boot Line updated IP Address:137.135.128.250 Gateway Address:137.135.128.1 Subnet Mask::ffffff00 Target Name: vxTarget User: gijxs03 lnIsa0 MAC Address: 00:60:38:8e:74:f5 lnIsa: lnIsa0 Reset lnIsa: lnIsa0 Reset ln79970 - IRQ INTC steered to IRQ15 ln79970HwInit: Device Type 0x2624 - LN79972 10/100BaseT lnPci1 MAC Address: 00:60:38:bd:57:50 Leader Pack: Using IP info from nvram Attached TCP/IP interface to lnIsa unit 0 Attaching network interface lo0... done. NFS client support not included. Adding 6239 symbols for standalone. ]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]] ]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]] ]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]] ]]]]]]]]]]] ]]]] ]]]]]]]]]] ]] ]]]] (R) ] ]]]]]]]]] ]]]]]] ]]]]]]]] ]] ]]]] ]] ]]]]]]] ]]]]]]]] ]]]]]] ] ]] ]]]] ]]] ]]]]] ] ]]] ] ]]]] ]]] ]]]]]]]]] ]]]] ]] ]]]] ]] ]]]]] ]]]] ]]] ]] ] ]]] ]] ]]]]] ]]]]]] ]] ]]]]]]] ]]]] ]] ]]]] ]]]]] ] ]]]] ]]]]] ]]]]]]]] ]]]] ]] ]]]] ]]]]]]] ]]]] ]]]]]] ]]]]] ]]]]]] ] ]]]]] ]]]] ]] ]]]] ]]]]]]]] ]]]] ]]]]]]] ]]]]] ] ]]]]]] ] ]]] ]]]] ]] ]]]] ]]]] ]]]] ]]]] ]]]]]]]] ]]]]] ]]] ]]]]]]] ] ]]]]]]] ]]]] ]]]] ]]]] ]]]]] ]]]]]]]]]] ITG Login: Copyright (c) 1993-1996 RST Software Industries Ltd. Israel. All righ ts reserved ver: 2.6 FCS Disk Check In Progress ... total disk space (bytes) : 3,923,968 bytes in each allocation unit : 2,048 total allocation units on disk : 1,916 bad allocation units : 0 available bytes on disk : 1,906,688 available clusters on disk : 931 maximum available contiguous chain (bytes) : 1,904,640 available space fragmentation (%) : 1 clusters allocated : 985 Done Checking Disk. Console logging enabled JUL 20 09 39 tITGStart: Info ITGL 2.10.63No inet address specified for interface lnPci1. JUL 20 09 39 tITGStart: Info ITG5000 Card initialized, all alarms cleared. (202) JUL 20 09 39 tITGStart: Info ELAN IP = 137.135.128.250JUL 20 09 39 tITGStart: Info Card TN = 0 0 0JUL 20 09 39 tLogTask: Info Completed addition of ITG MIB tree 1.3.6.1.4.1.562 JUL 20 09 39 tLogTask: Info MMsend called by appl 9 before Meridian Manager Init! JUL 20 09 39 tLogTask: Info MMsend called by appl 9 before Meridian Manager Init! JUL 20 09 39 tLogTask: Info MMsend called by appl 9 before Meridian Manager Init! JUL 20 09 39 tLogTask: Info XA : - Create MsgQ (Pointer)JUL 20 09 39 tLogTask: Info XA : - Register with M-1 ManagerJUL 20 09 39 tLogTask: Info XA : - Spawn xaTask()JUL 20 09 39 tLogTask: Info Task Spawned OKJUL 20 09 39 tITGStart: Info XA : - Query 8051XA for Dongle IDJUL 20 09 39 tXA: Info Got Dongle ResponseJUL 20 09 39 tXA: Info Invalid Family Code 0x0JUL 20 09 39 tITGStart: Warning Interface lnPci1 is not configuredMXP environment is created. JUL 20 09 39 tITGStart: Info Configuring Voice LAN on lnIsa0, IP = 137.135.128.250 JUL 20 09 39 tXA: Info Got Version ResponseJUL 20 09 39 tXA: Info Version : ITG Firmware Rls 5.0JUL 20 09 39 tITGStart: Info itgStartAppBeginJUL 20 09 39 tITGStart: Info Starting applicationsJUL 20 09 39 tITGStart: Info rudpMgrRunJUL 20 09 39 tRDP: Info RUDP waiting for messages.JUL 20 09 39 tITGStart: Info mamInitJUL 20 09 39 tMAM: Info MAM startedJUL 20 09 39 tITGStart: Info dimInitJUL 20 09 40 tITGStart: Info DSP memory tests passed on DSP 0JUL 20 09 40 tITGStart: Info DSP memory tests passed on DSP 1JUL 20 09 41 tITGStart: Info DSP memory tests passed on DSP 2JUL 20 09 41 tITGStart: Info DSP memory tests passed on DSP 3JUL 20 09 41 tXA: Info Got Serial Number ResponseJUL 20 09 41 tXA: Info Serial : NNTMG70A1BDD 20024JUL 20 09 42 tITGStart: Info DSP memory tests passed on DSP 4JUL 20 09 42 tITGStart: Info DSP memory tests passed on DSP 5JUL 20 09 42 tA07: Info A07 (00) 0x30 0x00 Board DownloadJUL 20 09 42 tA07: Info - Companding Law=Mu-LawJUL 20 09 42 tA07: Info - BoardParam->10PPS1 Make/Break Ratio=0x00JUL 20 09 42 tA07: Info Companding Law set to MuLawJUL 20 09 42 tA07: Warning Preferred codec not set up yetJUL 20 09 42 tA07: Info A07 (00) 0x31 0x00 Board DownloadJUL 20 09 42 tA07: Info - BoardParam->10PPS2 Make/Break Ratio=0x00JUL 20 09 42 tA07: Info Companding Law set to MuLawJUL 20 09 42 tA07: Warning Preferred codec not set up yetJUL 20 09 42 tA07: Info A07 (00) 0x32 0x00 Board DownloadJUL 20 09 42 tA07: Info - BoardParam->20PPS Make/Break Ratio=0x00JUL 20 09 42 tA07: Info Companding Law set to MuLawJUL 20 09 42 tA07: Warning Preferred codec not set up yetJUL 20 09 42 tA07: Info A07 Channel download ignoredJUL 20 09 42 tA07: Info A07 class of service download ignoredJUL 20 09 42 tA07: Warning A07 Pack msg 0xe ignoredJUL 20 09 42 tA07: Info A07 Channel download ignoredJUL 20 09 42 tA07: Info A07 class of service download ignoredJUL 20 09 42 tA07: Warning A07 Pack msg 0xe ignoredJUL 20 09 42 tA07: Info A07 Channel download ignoredJUL 20 09 42 tA07: Info A07 class of service download ignoredJUL 20 09 42 tA07: Warning A07 Pack msg 0xe ignoredJUL 20 09 42 tA07: Info A07 Channel download ignoredJUL 20 09 42 tA07: Info A07 class of service download ignoredJUL 20 09 42 tA07: Warning A07 Pack msg 0xe ignoredJUL 20 09 42 tA07: Info A07 Channel download ignoredJUL 20 09 42 tA07: Info A07 class of service download ignoredJUL 20 09 42 tA07: Warning A07 Pack msg 0xe ignoredJUL 20 09 42 tA07: Info A07 Channel download ignoredJUL 20 09 42 tA07: Info A07 class of service download ignoredJUL 20 09 42 tA07: Warning A07 Pack msg 0xe ignoredJUL 20 09 42 tA07: Info Units enabled : 0x1JUL 20 09 42 tA07: Info - Board enabled - LED OFFJUL 20 09 42 tA07: Info Unit 0 enabledJUL 20 09 42 tA07: Info First channel enabled on cardJUL 20 09 42 tA07: Info Card state ENBLJUL 20 09 42 tA07: Info Unit 1 enabledJUL 20 09 42 tA07: Info Unit 2 enabledJUL 20 09 42 tA07: Info Unit 3 enabledJUL 20 09 42 tA07: Info Unit 4 enabledJUL 20 09 42 tA07: Info Unit 5 enabledJUL 20 09 42 tA07: Info Unit 6 enabledJUL 20 09 42 tA07: Info Unit 7 enabledJUL 20 09 42 tA07: Info Unit 8 enabledJUL 20 09 42 tA07: Info Unit 9 enabledJUL 20 09 42 tA07: Info Unit 10 enabledJUL 20 09 42 tA07: Info Unit 11 enabledJUL 20 09 42 tA07: Info Unit 12 enabledJUL 20 09 42 tA07: Info Unit 13 enabledJUL 20 09 42 tA07: Info Unit 14 enabledJUL 20 09 42 tA07: Info Unit 15 enabledJUL 20 09 42 tA07: Info Unit 16 enabledJUL 20 09 42 tA07: Info Unit 17 enabledJUL 20 09 42 tA07: Info Unit 18 enabledJUL 20 09 42 tA07: Info Unit 19 enabledJUL 20 09 42 tA07: Info Unit 20 enabledJUL 20 09 42 tA07: Info Unit 21 enabledJUL 20 09 42 tA07: Info Unit 22 enabledJUL 20 09 42 tA07: Info Unit 23 enabledJUL 20 09 43 tITGStart: Info DSP memory tests passed on DSP 6JUL 20 09 43 tITGStart: Info DSP memory tests passed on DSP 7JUL 20 09 43 tITGStart: Info Found 8 DSP devices in systemJUL 20 09 43 tITGStart: Info Detected 8 DSP devices, 24 channelsJUL 20 09 43 tMVX_XSPY: Info 0000005968 - DIM: Created.JUL 20 09 44 tMVX_XSPY: Info 0000006468 - ROOT: gg_perm_malloc: 256 bytes at 0x0049E158 JUL 20 09 44 tMVX_XSPY: Info 0000006468 - ROOT: gg_perm_malloc: 18400 bytes at 0x0049E258 JUL 20 09 44 tMVX_XSPY: Info 0000006468 - ROOT: gg_perm_malloc: 2784 bytes at 0x004A2A38 JUL 20 09 44 tMVX_XSPY: Info 0000006468 - ROOT: gg_perm_malloc: 5280 bytes at 0x004A3518 JUL 20 09 44 tITGStart: Info ommInitJUL 20 09 44 tITGStart: Info tpsStartJUL 20 09 44 tVTM: Info tos 0xc, precedence 0x5JUL 20 09 44 tVTM: Info jitter 0x32, HighWaterMark 0x64JUL 20 09 44 tVTM: Info VTM StartedJUL 20 09 44 tVTM: Info vtm initializedJUL 20 09 44 tVTI: Info vtiILib initializingJUL 20 09 44 tITGStart: Info Survival IP = 0.0.0.0JUL 20 09 46 tITGStart: Info Waiting for PBX RUDP link to be established...JUL 20 09 46 tITGStart: Info PBX RUDP link establishedJUL 20 09 46 tITGStart: Info PBX TCP link not usedJUL 20 09 46 tITGStart: Warning Cannot open the file /C:/data/reduip.txt to read. JUL 20 09 46 tSET: Info StartedJUL 20 09 46 tSET: Info tone table replacedJUL 20 09 46 tSET: Info cadence table replacedJUL 20 09 46 tVTM: Info Client logged on 0x17F8CFCJUL 20 09 46 tCSV: Info CSV task startedJUL 20 09 46 tTCK: Info TPS Socket Engine StartedJUL 20 09 46 tTPS: Info TPS StartedJUL 20 09 46 tTPS: Info DBSync Request sent to CSJUL 20 09 46 tITGStart: Info FW file uncompressJUL 20 09 47 tITGStart: Info Get FW version 3002B00 from uncompressed file /ums/fwfile JUL 20 09 48 tUMS: Info server stub task started as "tUMS"JUL 20 09 48 tCSV: Info call server using the long TN formatJUL 20 09 48 tSET: Info tftp /u/db/itg_dnld/tone.tblJUL 20 09 48 tVTM: Info Client logged on 0x13E9B90JUL 20 09 48 tRTP: Info vgw rtp task startedJUL 20 09 48 tRTCP: Info vgw rtcp task startedJUL 20 09 48 tUMC: Info client stub registered with UMS server as 0x13e9cdcJUL 20 09 48 tVGW: Info vgw task startedJUL 20 09 48 tVGW: Info channel setup for 24 port daughtercard, trunkType 0JUL 20 09 48 tMAM: Info Own card IP = 137.135.128.250JUL 20 09 48 tMAM: Info notifyConfigReadDone for 24 channelsJUL 20 09 48 tMAM: Info Initiate download request for codec 1JUL 20 09 48 tITGStart: Info All TPS modules started!JUL 20 09 48 tITGStart: Info itgStartAppEndJUL 20 09 48 tITGStart: Info All applications startedJUL 20 09 48 tMVX_DIM: Info Download codec image completed -DSP# 0, Image Id= 0 JUL 20 09 49 tSET: Info tftp successJUL 20 09 49 tSET: Info tone table replacedJUL 20 09 49 tSET: Info tftp /u/db/itg_dnld/cadence.tblJUL 20 09 50 tMVX_DIM: Info Download codec image completed -DSP# 1, Image Id= 0 JUL 20 09 50 tSET: Info tftp successJUL 20 09 50 tSET: Info cadence table replacedJUL 20 09 50 tMVX_DIM: Info Download codec image completed -DSP# 2, Image Id= 0 JUL 20 09 51 tMVX_DIM: Info Download codec image completed -DSP# 3, Image Id= 0 JUL 20 09 51 tMVX_DIM: Info Download codec image completed -DSP# 4, Image Id= 0 JUL 20 09 52 tMVX_DIM: Info Download codec image completed -DSP# 5, Image Id= 0 JUL 20 09 52 tMVX_DIM: Info Download codec image completed -DSP# 6, Image Id= 0 JUL 20 09 53 tMVX_DIM: Info Download codec image completed -DSP# 7, Image Id= 0 JUL 20 09 53 tVGW: Info Registering 24 channelsJUL 20 09 53 tMAM: Info rte: Empty configRouteTable!JUL 20 09 54 tVGW: Info Channel 0, is UNEQUIP on CS, tn 0x0000JUL 20 09 54 tVGW: Info Channel 1, is UNEQUIP on CS, tn 0x0001JUL 20 09 54 tVGW: Info Channel 2, is UNEQUIP on CS, tn 0x0002JUL 20 09 54 tVGW: Info Channel 3, is UNEQUIP on CS, tn 0x0003JUL 20 09 54 tVGW: Info Channel 4, is UNEQUIP on CS, tn 0x0040JUL 20 09 54 tVGW: Info Channel 5, is UNEQUIP on CS, tn 0x0041JUL 20 09 54 tVGW: Info Channel 6, is UNEQUIP on CS, tn 0x0042JUL 20 09 54 tVGW: Info Channel 7, is UNEQUIP on CS, tn 0x0043JUL 20 09 54 tVGW: Info Channel 8, is UNEQUIP on CS, tn 0x0080JUL 20 09 54 tVGW: Info Channel 9, is UNEQUIP on CS, tn 0x0081JUL 20 09 54 tVGW: Info Channel 10, is UNEQUIP on CS, tn 0x0082JUL 20 09 54 tVGW: Info Channel 11, is UNEQUIP on CS, tn 0x0083JUL 20 09 54 tVGW: Info Channel 12, is UNEQUIP on CS, tn 0x00c0JUL 20 09 54 tVGW: Info Channel 13, is UNEQUIP on CS, tn 0x00c1JUL 20 09 54 tVGW: Info Channel 14, is UNEQUIP on CS, tn 0x00c2JUL 20 09 54 tVGW: Info Channel 15, is UNEQUIP on CS, tn 0x00c3JUL 20 09 54 tVGW: Info Channel 16, is UNEQUIP on CS, tn 0x0100JUL 20 09 54 tVGW: Info Channel 17, is UNEQUIP on CS, tn 0x0101JUL 20 09 54 tVGW: Info Channel 18, is UNEQUIP on CS, tn 0x0102JUL 20 09 54 tVGW: Info Channel 19, is UNEQUIP on CS, tn 0x0103JUL 20 09 54 tVGW: Info Channel 20, is UNEQUIP on CS, tn 0x0140JUL 20 09 54 tVGW: Info Channel 21, is UNEQUIP on CS, tn 0x0141JUL 20 09 54 tVGW: Info Channel 22, is UNEQUIP on CS, tn 0x0142JUL 20 09 54 tVGW: Info Channel 23, is UNEQUIP on CS, tn 0x0143JUL 20 09 54 tVGW: Info Card state UNEQJUL 20 09 54 tTPS: Notice Lost contact with master 0.0.0.0, calling an election JUL 20 09 56 tCSV: Info CSV enableJUL 20 09 56 tCSV: Info Node 0 registering for terminal connections on 0.0.0.0:4100 JUL 20 09 56 tTPS: Notice Election won, master = 137.135.128.250JUL 20 09 56 tNetTask: Info duplicate IP address 00000000 sent from ethernetaddress 00 84:f1:0d:c0 | ||||||||
| | |
| | #5 (permalink) | ||||||||
| Junior Member ![]()
Location: Jacksonville, AR Rep Power: 6 ![]() | As embarrasing as this may seem, yes, that was similar to my problem. I don't know the correct termonoligy, but its up and working now. When I got that first VoIP phone working, it was like having a child. When I saw it connecting to the card and upgrading the firmware, my heart stopped and I cried tears of joy. Then, when I got dialtone and heard a person at the other end say something, and it was CRYSTAL clear, I was, no, I am the most happiest person on this planet. VoIP, here I come! | ||||||||
| | |
![]() |
| Currently Active Users Viewing This Thread: 1 (0 members and 1 guests) | |
| Thread Tools | |
| Display Modes | |
| |
Similar Threads | ||||
| Thread | Thread Starter | Forum | Replies | Last Post |
| OPTION 81 and Accord Bridge | monicker | Meridian Systems | 3 | 09-15-2003 07:32 AM |
| how do i configure xfcot ? | arch4 | Meridian Systems | 1 | 06-19-2003 06:37 PM |
| MAT Internal Call Detail Recording? | Rachelle | Meridian Systems | 6 | 05-20-2003 12:33 PM |
| How to Configure PRI to be B8ZF | Diny | Meridian Systems | 10 | 12-20-2002 07:15 AM |
| CISCO AVVID solution and Option 61C | daved | Meridian Systems | 3 | 12-18-2002 03:44 PM |