John_In_Dakota

What is it you need help on? There is a certain way to put these in.

john

__________________
Thankful for everything...at least today.

Lucylu

I have two Loops that were used by another company before we took over the PBX. 82 & 83. When I stat them in LD 32 they come up as UNEQ. When I try to build Tie's in LD 14, no matter what I do I receive errors. I'veonly done this once before and can't remember exactly what to do. This is what I see when I try to build route members in LD 14 this is what I see

TNS AVAIL: 2798 USED: 702 TOT: 3500
RAN CON AVAIL: 5 USED: 16 TOT: 21
MUS CON AVAIL: 0 USED: 192 TOT: 1
AST AVAIL: 20 USED: 0 TOT: 20
REQ new 24
TYPE tie
TN 82 0 1

SCH5786
TN

jack

You need to tell the switch that these loops are there.

You will do this in LD 17 gate opener CEQU.

If you need more specifics post back.

Good luck!!

Jack

__________________
Dogs rollover Phones hunt

gei_spot

SCH5786

This is telling you that the loop does not exist. You will need to create loop 82 in LD 17 before you can add members.

__________________
I'm a member of the "PbxInfo Gang"

Lucylu

If you do have information on how to build in LD 17 CEGU it would be great, thanks

freddog

You add the loop at the DLOP prompt. The MODE and LCMT will depend on what you're building. The MODE options are LINK, PRI, or TRK. The LCMT options are B8S (for B8ZS) or AMI.

scott

Freddog...keep the tips comin!!

Reusser

T1 implementation

1 - LD 73 - Define error detection thresholds (this may allready be done)
2 - LD 17 - Add DTI Loop
3 - LD 16 - Define Route
4 - LD 14 - Define trunks
5 - LD 73 - Define Clock (this may already be done)

Examples -

LD 73
Req: New
Type: DDB
TRSH: <-- enter number to be used 0-15. I usually use 0
RALM: 128
BIPC: 0
LFAC: 0


LD 17
Req: CHG
Type: CEQU
DLOP: C dd ff (82 24 esf)
C = Loop number of T1 - 82
dd = number of data calls allowed on this t1 - 24
ff = Frame format used D2, D3, D4, ESF - ESF
Mode: TRK
TRSH: <-- enter the TRSH number from LD 73



LD 16
Req: NEW
Type: RDB
Route: <-- enter a route number not used
TKTP: <-- enter the trunk type usually either DID or TIE
DTRK: yes
ICOG: IAO <-- for in and out, could be in only or out only
ACOD: <-- enter access code for route. must be unique number
CNTR: YES
NEDC: ETH
FEDC: ETH

If you have music on hold or CDR respond according to the prompts. Check another route.


LD 14
REQ: NEW 24
Type: <-- enter the same type as you put in for route - usually DID or TIE
TN: 82 1 <-- enter the starting TN
NCOS: <-- enter the ncos access you want these trunks to have
RTMB: <-- enter the route number you built
SIGL: <-- enter the signaling type - check with the other end usually EM4
STRO: <-- enter the starting arrangement - WNK the best
STRI: <-- enter the starting arrangement - WNK the best
CLS: DTN


LD 60
ENLL 82 <-- to enable loop 82. assuming all cables are connected and the CO is ready.