| |||||||||
 |
| ||||||||
| |||||||||||||||
| |||||||||||||||
| Meridian Systems Welcome to the Nortel Meridian Forums Including Meridian Options 11-81C CS1000M Meridian Mail Call Pilot Companion and Sucession Hospitality OTM MAT MICB RAN NetGateway ..., and all other Applications |
| Tags: continue, disconnect, end, far, near, ring, trunk |
  |
| | LinkBack | Thread Tools | Display Modes |
 09-18-2003, 03:50 PM | #1 (permalink) | ||||||||
| Junior Member
Location: Canada Rep Power: 0  | Hi, I've got a little problem with my COT trunk. I have an Option 11 release 24. For the moment, I have one Cot trunk (Loop start) on a NT8D14BB (Universal trunk card). The problem is with incoming calls. When a call is placed (far end) from the outside to my number (near end), and the far end goes on-hook while its ringing, the near end (my pbx) continue to ring and never stops.... Now I'm confused, can you help me? Is it the Loop start? I don't think because I tried with a ground start line and it's the same thing. I tried also NEDC and FEDC in load 16 with ETH or ORG...nothing changed. Any ideas? Thank you! | ||||||||
 |   |
| 09-18-2003, 05:18 PM | #2 (permalink) |
| Admin  | Co trunk - Far end disconnect, Near end continue to ring! bibendum - You're on the right track (I think). If you've got the control set to Originator or Either - the switch should see the Half-Disconnect and idle the call. Maybe your should check your DSI Timer (Disconnect Supervision) in LD 16... |
| | |
| 09-18-2003, 05:22 PM | #3 (permalink) |
| Admin | It looks Right.... That last reply went haywire???? Lets try this again...... bibendum - You're on the right track (I think). If you've got the control set to Originator or Either - the switch should see the Half-Disconnect and idle the call. Maybe you should check your DSI Timer (Disconnect Supervision) in LD 16....... Good Luck |
| | |
| 09-18-2003, 05:24 PM | #4 (permalink) |
| Admin | That last reply went haywire???? Lets try this again...... bibendum - You're on the right track (I think). If you've got the control set to Originator or Either - the switch should see the Half-Disconnect and idle the call. Maybe you should check your DSI Timer (Disconnect Supervision) in LD 16....... Good Luck |
| | |
| 09-18-2003, 05:38 PM | #5 (permalink) |
| Senior Member  | Prometric test It's actually the NRD (No Ring Detection) timer that you want to check. When ringing voltage is removed, the M1 starts this timer and will assume incoming caller has disconnected when it times out. It should be set to slightly longer than the "off" ringing cycle. |
| | |
| |
| Currently Active Users Viewing This Thread: 1 (0 members and 1 guests) | |
| Thread Tools | |
| Display Modes | |
| |
 Similar Threads | ||||
| Thread | Thread Starter | Forum | Replies | Last Post |
| Force Disconnect | MarcReid | Meridian Systems | 4 | 06-21-2006 07:53 AM |
| Trunk measurements | Switchtek | Definity Support | 7 | 01-02-2006 10:25 AM |
| CHage UNR for all sets | Meridian Systems | 7 | 03-02-2004 12:59 PM | |
| Trunk to Trunk connection woes... | Hi-Tech | Meridian Systems | 2 | 02-05-2003 07:25 PM |
Linear Mode
