| |||||||||
 |
| ||||||||
| |||||||||||||||
| |||||||||||||||
| Meridian Systems Welcome to the Nortel Meridian Forums Including Meridian Options 11-81C CS1000M Meridian Mail Call Pilot Companion and Sucession Hospitality OTM MAT MICB RAN NetGateway ..., and all other Applications |
| Tags: did |
 |
| | LinkBack | Thread Tools | Display Modes |
 07-29-2008, 05:05 PM | #1 (permalink) | ||||||||
| Junior Member
Rep Power: 0  Country:  | DID Setup The system is a CS1000. I have several blocks of DID and Inward numbers. Usually the last 4 digits match the ext. I simply add the ext and the DID number is now directed to that ext. I don't know how to program an ext to use a DID number that is out of the range of my extensions. Where in the programming that pairs the DID number to the ext. How do I print this database and what load do I need to make changes | ||||||||
 |   |
| 07-29-2008, 05:38 PM | #2 (permalink) | ||||||||
| Senior Member   gei_spot is going phishing
Location: Somewhere in this vast universe on a little rock that looks like a grape. Rep Power: 12 Gender:  Country:  | Are you trying to add non-DIDs to a set? You can print the unused numbers in LD 20 REQ prt TYPE ludn CUST 0 DN xxxx - or leave this blank to get all avail numbers in the system. __________________  I'm a member of the "PbxInfo Gang" | ||||||||
| | |
| 07-29-2008, 07:17 PM | #3 (permalink) | ||||||||
| Senior Member 
Rep Power: 0 Gender:  Country:  | You can use..IDc table.....ld 49 and add it in the RDB..ld 16 ld 49--new --idc--dcno ld 16-idc- yes DCNO- table number which u have created in ld 49 the IDC table is nothing but incoming digit convertion table... if you want a DID number 4000 to reach extension 5000 then in IDC table 4000 will be comverted to 5000 and this table should be added in ld 16 RDB. i guess this is what you want....  | ||||||||
| | |
| 08-08-2008, 05:05 PM | #7 (permalink) | ||||||||
| Junior Member
Rep Power: 0 Country: | Thanks everyone I was able to print the current information and make the required changes. However this list is rather small. I quess this is just the exceptions to a rule that is defined elsewhere for the bulk of my DID's. I have several hundred DID's with the last 4 digits matching the ext. Where is that info? | ||||||||
| | |
| 08-08-2008, 06:02 PM | #8 (permalink) | ||||||||
| Senior Member gei_spot is going phishing
Location: Somewhere in this vast universe on a little rock that looks like a grape. Rep Power: 12 Gender: Country: | here Are you trying to add non-DIDs to a set? You can print the unused numbers in LD 20 REQ prt TYPE ludn CUST 0 DN xxxx - or leave this blank to get all avail numbers in the system. Whatever doesn't print is being used. or REQ prt TYPE dnb CUST 0 DN - leave this blank and all numbers programed in your system will print could be pretty lengthy though. __________________ I'm a member of the "PbxInfo Gang" Last edited by gei_spot; 08-08-2008 at 06:06 PM. | ||||||||
| | |
|
| Currently Active Users Viewing This Thread: 1 (0 members and 1 guests) | |
| Thread Tools | |
| Display Modes | |
| |
 Similar Threads | ||||
| Thread | Thread Starter | Forum | Replies | Last Post |
| DID setup | Sniff | BCM and Norstar | 3 | 08-29-2008 10:07 PM |
| MGC setup | Sinner | Meridian Systems | 3 | 02-15-2008 02:23 PM |
| BCM 400 UPS setup | jbartling | BCM and Norstar | 1 | 08-27-2007 12:25 PM |
| TIE setup | justzikle | Meridian Systems | 1 | 05-20-2007 10:45 AM |
| PTY setup | Splinters | Meridian Systems | 2 | 02-09-2004 07:13 PM |
Linear Mode
