| |||||||||
 |
| ||||||||
| |||||||||||||||
| |||||||||||||||
| Meridian Systems Welcome to the Nortel Meridian Forums Including Meridian Options 11-81C CS1000M Meridian Mail Call Pilot Companion and Sucession Hospitality OTM MAT MICB RAN NetGateway ..., and all other Applications |
| Tags: 4ess, custom, kickin, pri |
 |
| | LinkBack | Thread Tools | Display Modes |
 07-24-2003, 02:14 PM | #1 (permalink) | ||||||||
| Junior Member 
Location: Alpharetta, GA Rep Power: 6  | Nortel NTP Updates - Release Notes I have an AT&T One Net PRI I am trying to cut over on my 81C. I seem to get the D channel stable but the Dual PRI card seems to remain in a red alarm state. I have heard that some people actually configure these 4E PRI's as TIE's with D channel rather than as PRI or DID. I know the circuit and CSU is good because I have made in-and-out calls on other equipment (BCM, 3Com NBX). Muchas Gracias. :casstet: | ||||||||
 |   |
| 07-24-2003, 02:47 PM | #2 (permalink) | ||||||||
| Senior Member  Rachelle is curious
Location: Lou, KY Rep Power: 9 Country:  | Adapt 2 wire low volt 24watt housephone to t/r When I used AT&T I had all of my T1's set as TIE. rlc __________________ No matter where you go, there is the Ladies Love Marty Fan Club. :bow2: :bow2: :bow2: | ||||||||
| | |
| 07-24-2003, 05:25 PM | #3 (permalink) | ||||||||
| Junior Member
Rep Power: 6 | Adapt 2 wire low volt 24watt housephone to t/r pri's should be setup as did's. make sure your co is sending ess4 signaling, and not ni1 or ni2. make sure your route and dch(adan) are setup as ess4. you may even try ess5 if all else fails. | ||||||||
| | |
| 07-25-2003, 12:41 AM | #4 (permalink) | ||||||||
| Junior Member
Location: Kansas City Rep Power: 6 | Blonde Joke I have a PRI on a 4ESS and have it set to DID. It is working fine. The only problems I had was the switch had to be set up to send out what call type it was. Mine was Megacom. Made that change and it came right up. | ||||||||
| | |
| 07-25-2003, 03:49 PM | #6 (permalink) | ||||||||
| Junior Member
Location: Alpharetta, GA Rep Power: 6 | In need of ssc with rls 25.40 Yes. loopback works fine. I know circuit is good because I can move it to other boxers like BCM or 3Com and works perfectly (this is a lab environment). Thanks for all the suggestions, will work on this weekend some more. | ||||||||
| | |
|
| Currently Active Users Viewing This Thread: 1 (0 members and 1 guests) | |
| Thread Tools | |
| Display Modes | |
| |
 Similar Threads | ||||
| Thread | Thread Starter | Forum | Replies | Last Post |
| Avaya question | gnrpatience | Definity Support | 3 | 08-08-2003 03:29 PM |
| Real Tuff ONE! | Twisted | Meridian Systems | 12 | 08-01-2003 06:48 PM |
| Blonde Joke | PD | Off Topic - Humor/Jokes | 1 | 07-24-2003 08:56 PM |
| Nortel NTP Updates - Release Notes | gwebster | Meridian Systems | 1 | 07-24-2003 02:56 PM |
Linear Mode
