slagburn

Your TIE line should be members in a route thus you need a route list index RLI that point to that route (LD 86) before doing your RLI you will need to identify any digit manipulation that needs to take place through a digit manipulation index DMI (also LD 86) after this is complete and you have a valid RLI number that points to the TIE route can you actually point the numbers to it - there are a variety of ways to do this one of which is CDP in LD 87.

takmsdsm

ok i think i figured it out...

here is my route..

Quote:



REQ: prt
TYPE: rdb
CUST 0
ROUT 12

TYPE RDB
CUST 00
DMOD
ROUT 12
DES FAX
TKTP TIE
NPID_TBL_NUM 0
ESN NO
CNVT NO
SAT NO
RCLS EXT
DTRK NO
PTYP ATT
AUTO NO
DNIS NO
ICOG OGT
SRCH RRB
STEP
ACOD 2007
TARG 01
CLEN 1
OABS
INST
IDC NO
DCNO 0 *
NDNO 0
DEXT NO
ANTK
SIGO STD
STYP SDAT
TIMR ICF 512
OGF 512
EOD 13952
DSI 34944
NRD 10112
DDL 70
ODT 4096
RGV 640
GRD 896
SFB 3
TFD 0
SST 5 0
NEDC ORG
FEDC ORG
CPDC NO
DLTN NO
HOLD 02 02 40
SEIZ 02 02
SVFL 02 02
CDR NO
MUS NO
RACD NO
MANO NO
FRL 0 0
FRL 1 0
FRL 2 0
FRL 3 0
FRL 4 0
FRL 5 0
FRL 6 0
FRL 7 0
TTBL 0
OHTD NO


PAGE 002

PLEV 2
ALRM NO
ART 0
SGRP 0
AACR NO

here is my trunk settings

Quote:


REQ: prt
TYPE: tnb
TN 13 0
DATE
PAGE
DES

TN 013 0 00 00
TYPE TIE
CDEN 8D
CUST 0
XTRK XUT
LDOP LOOP
TIMP 600
BIMP 3COM
TRK ANLG
NCOS 0
RTMB 12 1
TGAR 1
SIGL LDR
STRO WNK
SUPN NO
AST NO
IAPG 0
CLS CTD DTN CND WTA LPR APN THFD
P10 NTC
TKID
DATE 12 JUN 2006

here is my new RLI settings

Quote:


RLI 8
ENTR 0
LTER NO
ROUT 12
TOD 0 ON 1 ON 2 ON 3 ON
4 ON 5 ON 6 ON 7 ON
CNV NO
EXP NO
FRL 0
DMI 0
FCI 0
FSNI 0
SBOC NRR
CBQ NO

ISET 0
NALT 5
MFRL 0

and here are my new CDP settings...

Quote:


REQ prt
CUST 0

FEAT cdp
TYPE dsc
DSC 408
DSC 408
FLEN 0
DSP LSC
RLI 8
NPA
NXX

The only problem im getting now is that im just getting a fast busy when i try and test...

slagburn

Just so we know... is the T1 circuit up and IDLE? Are the trunk settings correct in terms of start arangement and such?

The programming looks good, if you are dealing with a fixed number of digits you can adjust the FLEN prompt to match... that will speed up call processing a bit.

Try tracking from the station that you're making calls from and see where you're getting blocked.