Midnight routine 30 not working - PBX Info :: Your Free PBX, PABX and Telephone Information Resource

Steevo · 06-07-2006, 12:20 PM

hey guys. I have a problem.

We recently have had a lot of people moving around, unplugging their phones etc. As a result we have lots of TN's being used without a set on the end of the line. So i added ovly 30 to the DROL

I checked this morning and no TN's have been freed up. I know for sure that there are lines with no sets on them

So i went back in and added program 30 to BKGD and i sat and watched the console output the following

The enties witn NWS501 are TN's that have been reported as having no digital set on the end are they not? but when i check with LUVU none of them are showing as free

NWS501 5 : -11

NWS401 6 : -8 -12

NWS501 9 : -12

NWS501 12 : -10

NWS301 -13 -14 -15 -16

NWS501 19 : -7

NWS301 -22 -23 -24

NWS501 25 : -12

NWS401 26 : -3 -8

NWS501 27 : -11

NWS301 -31 -32

NWS301 -34 -35 -36

AUD000

CSC120 7 0 0 12 7206

DTC103

DCH: 10 MAINT INDICATION TIME: 16:53:44
COUNTER VALUE
3 255

TIM030 17:00 7/6/2006 CPU 0

NWS501 5 : -11

NWS401 6 : -8 -12

NWS501 9 : -12

NWS501 12 : -10

NWS301 -13 -14 -15 -16

DTC103

NWS501 19 : -7

NWS301 -22 -23 -24

NWS501 25 : -12

NWS401 26 : -3 -8

NWS501 27 : -11

NWS301 -31 -32

NWS301 -34 -35 -36

Here's a prt of the ovly in LD 17

OVLY
SID 30
BKGD 044
PBXH 02
TODR 02 (Time of Daily Routine)
DROL 030 043 044 135 (Daily routine Overlay)

MULTI_USER ON

jack · 06-07-2006, 12:43 PM

What the error is telling you is those TN's failed the signaling test and have been disabled.

Most likely there are not any phones attached, although there could be a phone or two that are on the "fritz" and that is why they failed.

To free up the TN's you will need to out the phones that failed after verifying that they in fact should not be there.

Steevo · 06-07-2006, 02:03 PM

Quote:

Originally Posted by jack

To free up the TN's you will need to out the phones that failed after verifying that they in fact should not be there.

That's strange. You see this feature used to be turned on a few years back and i'm sure the phone was automatically outed, i never used to have to out those TN's.

Does than make any sense?

Is there anything i can do to print a list of disabled TN's?

Billo · 06-07-2006, 02:29 PM

I agree with jack. LD 30 does not out the phones in software. It just disables the phones. You would have to do a lot of programming if the phones were removed from software for being unplugged.
Looks like you are working on an option 11.
You can look up the stat commands in LD 32.
For large switches you can list disabled phones with LDIS l s (loop and shelf)
For Option 11 use LDIS c (cabinet) Cabinets start with 0.
You can also enable all the TNs with ENLS c (cabinet)
You can also work at the card level. STAT c (card) or ENLC c (card)

colin · 06-07-2006, 03:01 PM

you can keep a Digital TN enabled by adding FLXA to the CLS of a set

this will not disable a port during the midnights if the set is unplugged

Steevo · 06-07-2006, 03:56 PM

Thanks guys great info yet again.

It turns out that we've had 50 TN's available to us for over two years that nobody knew anything about.

I should get a god damm bonus for this lol.

nortelzo@gmail.com · 06-08-2006, 06:06 PM

With rls 24 and later you can also use
LD 117 INV GENERATE SETS
after a while you got a message that the inventory has finished
and you can use INV PRT SETS
You get a nice list from the SETS.
You can check this list for wrong type of SETS according the programming.
Also unavailable sets are often not patched or unplugged.

Pennyman.

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Midnight Routine frozen	diversion	Meridian Systems	3	09-09-2005 08:27 AM
Sch1958 - Stuck in midnight routine	oakey70	Meridian Systems	4	02-09-2005 04:07 PM
Add commands to the midnight routine	HCJes	Meridian Systems	3	04-29-2004 07:52 AM
Midnight routine	stinson	Meridian Systems	2	03-17-2004 11:32 PM
Stopping a Midnight Routine	morpheus	Meridian Systems	3	02-10-2004 12:26 AM

Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)