612moto

Below the LD 49 FCR > PRT
REQ prt
TYPE fcr
CUST 0
CRNO

CRNO 0

CRNO 1
INIT DENY
ALOW 1 4
2 4
3 4
4 4
5 4
6 4
7 4
8 4
9 4
0 4

612moto

Unfortunately yesterday and day before that were to busy to dig into this. My thoughts monday were that a solution was right around the corner.

thoughts>
When making a set on the PBX with a 1010 DN>
Placed a test call to ext. 1112> display reads 2293????
attempted to call 1010 results were will not ring. ??????
If I dial 2293 the 1010 dn on the PBX rings ??????

Is this a clue?

A few weeks ago I had temporarily moved the 2293 extension to 1 0 1 0 TN for a office move.


REQ: prt
TYPE: tn


MARP NOT ACTIVATED

TN 0 0 1 0
DATE
PAGE
DES

DES HULT
TN 000 0 01 00
TYPE 500
CDEN 4D
CUST 0
DN 1010 0 MARP
AST NO
IAPG 0
HUNT
TGAR 1
LDN NO
NCOS 0
SGRP 0
RNPG 0
XLST
SCI 0
FNA HTD ONS FBD XFA WTA THFD
LPR XRD CWD SWD MWD LPD XHD CCSD LND TVD
CFTD SFD C6D CNID CLBD AUTU
ICDD CDMD EHTD MCTD
GPUD DPUD CFXA ARHD OVDD AGTD CLTD LDTD ASCD
MBXD CPFA CPTA DDGA NAMA
SHL ABDD CFHD
USRD BNRD OCBD RTDD FAXD PGND FTTC
RCO 0
PLEV 02
AACS NO
FTR CFW 4
DATE 8 JUN 2006



Any ideas on what is going on here?

612moto

Just made a change in LD 49:
FCR

TYPE fcr
CUST 0
CRNO

CRNO 0

CRNO 1
INIT DENY
ALOW 1 4
2 4
3 4
4 4
5 4
6 4
7 4
8 4
9 4
0 4
I added 10 4 to the allow group...

The result was the same>

>ld 96
DCH000
.enl msgi 22
.enl msgo 22
.
DCH 22 OMSG SETUP REF 00000017 CH 22 23 TOD 1034
CALLING #:7166654701 NUM PLAN: E163
CALLED #: NUM PLAN: E163

DCH 22 OMSG SETUP REF 00000017 CH 22 23 TOD 1038
CALLING #:7166654701 NUM PLAN: E163
CALLED #: NUM PLAN: E163

PRI241 DCH: 22 DATA: 00000017
DCH 22 OMSG REL COMP REF 00000017 CH 22 23 TOD 1042
CAUSE :NO USER RESPONDING


Note no digits are being sent.

612moto

I used the TRAC on extension 4701 and placed a call to 1112 and to 1070> Both of these DN's are on the same phone,,, and are able to be called from the Cisco system side. Notice when dialing the 1070 no called number??? No digits are being sent????



---- ISDN PRA CALL (TERM) ----
CALL REF # = 23
BEARER CAP = VOICE
CALL STATE = 4 DELIVERY
CALLING NO = 7166654701
CALLED NO = 1112



.trac 0 4701

ACTIVE TN 000 0 00 13
ORIG 000 0 00 13 0 SCR MARP 0 4701 2616
TERM 022 23 TIE RMBR 5 23
DIAL DN 1070
MAIN_PM DIAL AUX_PM COMPLETE
TALKSLOT ORIG 29 TERM 26
EES_DATA:
NONE
QUEU NONE
CALL ID 0 108


AUX NARS



---- ISDN PRA CALL (TERM) ----
CALL REF # = 23
BEARER CAP = VOICE
CALL STATE = 1 INIT
CALLING NO = 7166654701
CALLED NO =

612moto

does anybody have any ideas why the PBX is stripping the digits?

Is 1010 setup for anything behind the scenes,,,, I just don't know where to look?

One other thing I found that was really odd>


A few weeks back I moved a set. I temp mov to tn 0 0 1 0
the set DN was 2993


then last week while experimenting lfor a solution on this 10xx thing....

I made a set with a DN 1010 on TN 0 0 1 0

when placing a call to the 1010 set it would not ring
I had dialtone on this set,,,, then I attempted to call 1112 the call display said 2993?????
2993 had been totally wiped from that terminal number.

When calling 2993 the 1010 phone would ring,,,,, strange but true.


Any clue?

Is 10 a access code for something? and where do I begin to look?

Thanks

colin

i still think this could be corruption

make sure you have no 10 numbers set then dump the switch (EDD)

then sysload

then rebuild your 10 DSC

612moto

Will this cause down time?

what LD and what proceedure.

I know my way around ld 11, 86,87,80,90etc. but have never done what you are asking.

thanks

colin

yes it will be down for a few minuets

go into LD 10 & check for 10 numbers if there are any 10xxxxx numbers then check them out

if you have none then go into LD 43 and enter "at the dot" EDD ( equipment data dump)
when that has finished turn off the power at the power unit count to 10 and switch it back on...it should all come back ok... sometimes D chanells may need to be brought back if you have any that is....

are you happy to try that..

612moto

I will give it a try