pbxn

When you call from your phone and perform a trac/trak what digits does it show being outpulsed?

colin

try outing 10 and then print 10 in LD20 just to confirm there are no more 10xxx numbers floating around in the switch

612moto

I removed the CDP 10

then prt in ld 20

ld 20

PT0000
MARP NOT ACTIVATED

REQ: prt
TYPE: dnb
CUST 0
DN
DATE
PAGE
DES

DN 0
TYPE ATT
TN 000 0 11 00 14 JAN 2005
(2250)

DN 11
TYPE CDP
STCD DSC

DN 12
TYPE CDP
STCD DSC

DN 13
TYPE CDP
STCD DSC

DN 14
TYPE CDP
STCD DSC

DN 17
TYPE CDP
STCD DSC

DN 18
TYPE CDP
STCD DSC

DN 2001
CPND
NAME SCT Banner Training Room
XPLN 24
DISPLAY_FMT FIRST,LAST
TYPE 500
TN 004 1 05 00 MARP DES AUDIT 11 DEC 2000

612moto

The 10 does not to be apearing anywhere,,,,??? so why won't it pass the digits?

colin

Well it looks like corruption to me....

i suggest you out DSC 10 first
then dump the switch ( EDD ) and take a backup copy
then sysload to clear all the flags
then re-build DSC 10

Buckshot

Just for giggles, have you built any analog phones at your site with 10XX or even 10X? At least you can verify if you have corruption on YOUR side..not the far end.

612moto

Created new on Meridian DN 1010 ,,,,,, see ENTC below> I don't get it????
I also called the switchboard operator to see what extension I was callong from when calling from the newly created 1010 ,,,, she said 2293 shows on the display
REQ: prt
TYPE: dn
TYPE DNB


MARP NOT ACTIVATED

CUST 0
DN 1010
DATE
PAGE
DES

DN 1010
TYPE 500
TN 000 0 01 00 MARP DES HULT 8 JUN 2006


NACT
REQ: prt
TYPE: dn
TYPE DNB
CUST 0
DN 2293
DATE
PAGE
DES

DN 2293
CPND
NAME Dawn Columbare
XPLN 14
DISPLAY_FMT FIRST,LAST
TYPE 500
TN 000 0 01 02 MARP DES H 23 MAY 2006


NACT
REQ: prt
TYPE: tn
TYPE TNB
TN 0 0 1 0
DATE
PAGE
DES

DES HULT
TN 000 0 01 00
TYPE 500
CDEN 4D
CUST 0
DN 1010 0 MARP
AST NO
IAPG 0
HUNT
TGAR 1
LDN NO
NCOS 0
SGRP 0
RNPG 0
XLST
SCI 0
CLS CTD DTN FBD XFA WTA THFD FNA HTD ONS
LPR XRD CWD SWD MWD LPD XHD CCSD LND TVD
CFTD SFD C6D CNID CLBD AUTU
ICDD CDMD EHTD MCTD
GPUD DPUD CFXA ARHD OVDD AGTD CLTD LDTD ASCD
MBXD CPFA CPTA DDGA NAMA
SHL ABDD CFHD
USRD BNRD OCBD RTDD FAXD PGND FTTC
RCO 0
PLEV 02
AACS NO
FTR CFW 4
DATE 8 JUN 2006


NACT
REQ: ****
OVL000
>ld 80
TRA000
MARP NOT ACTIVATED

.entc 0 0 1 0 2300


gotr


.15:57:32 08/06/2006
IDLE TN 000 0 01 00


.15:57:42 08/06/2006
ACTIVE TN 000 0 01 00
ORIG 000 0 01 02 MARP 0 2293 500
TERM 000 0 01 00 MARP 0 1010 500
TDTN 12 SLOT 23 PTY SLOT 17
DIAL DN 1010
MAIN_PM RING AUX_PM
TALKSLOT ORIG 21 TERM 23
EES_DATA:
NONE
QUEU RING
CALL ID 0 6





.15:58:28 08/06/2006
IDLE TN 000 0 01 00


.

nortelzo@gmail.com

PRT the Route 22 , and try to dial ACOD and then 1070, does that work ?
How are the settings of the FRL in the route 22
Which NCOS does the set have and print the FCR in LD 49
maybe 10 is denied in the FCR table.
You can also do a trace during the call in LD 80 trac TN dev
that gives you more info about the call.

Pennyman.

ismael

Do you tried to change FLEN 4 to all DSC's?
Some time ago I have a similar problem with 3 PBX's with diferent number extension lengths (1, 4 & 5) and when I try to use the CDP with diferents FLEN some don't work with the same RLI and routes, so I use the FLEN = 5 to alls dsc's and the problem dissapear.
For an example: to call to some service in to PBX-3 (recording service) from PBX-1 I need dial a "8" and to call to an extension need to dial 2XXXX, so in my PBX-1 I put:
DSC 8
FLEN 1
DSP LSC
RLI 7
DSC 22
FLEN 5
DSP LSC
RLI 7
DSC 23
FLEN 5
DSP LSC
RLI 7
DSC 24
FLEN 5
DSP LSC
RLI 7
DSC 25
FLEN 5
DSP LSC
RLI 8
DSC 26
FLEN 5
DSP LSC
RLI 8


I can't dial the 8 don't work to the pbx-3 but I can dial to PBX-2 and PBX-3 the other cdp

when I cahnge the FLEN to 5 in DSC 8
I can dial the 8
why? I dont know but with the same FLEN work