Electronic lock on TIE lines - PBX Info :: Your Free PBX, PABX and Telephone Information Resource

justzikle · 04-15-2006, 11:37 AM

Hi all i have 5 different routes off COT lines and one route is of type=TIE. In my CCS Data CCRS=TLD.
Problem is that when i lock my set through ELKA it works good with all other routes accept TIE. I can easily access my TIE route(ACOD=90) even my set is lock by electronic lock. I tried CCRS=FR2. it works ok but it also restricts Transferring outside line to my ext. Isnt there anyway that i could restrict TIE lines also being access by an user having electronic lock enable, as other routes ae working fine.
(This tie system is working with 2 sites tied with E&M card, Dialing setup is normal which is "first ACOD then Ext. no.. can i change route type to get electronic lock works?? can i programme E&M route with DID or COT??

regards

TomasSouth · 04-15-2006, 04:48 PM

Keeping CRS=TLD maybe create another FCR table, as CRNO 1 as example. Define in CRNO 1 as INIT DENY. Then in TIE's RDB, define FRL 0 1.

justzikle · 04-16-2006, 12:56 AM

Tomas do i have to put "1" in all entries of FRL i mean 0 1 , 1 1 , 2 1 , 3 1 so on???
if no then how it works if i put FRL 0 1 only
regards.

TomasSouth · 04-16-2006, 01:03 AM

Before moving further, do all your telephones has CLS UNR and NCOS 0? I assume that way which is why my advice is like that. If yes, just FRL 0 1.

justzikle · 04-16-2006, 01:35 AM

Tomas i have almost 400 extensions programmed with cls tld and different NCOS values. Some are allowed to dial with electronic lock option , somes are unrestricted i mean cud dial without any lock or authcode and some are block havind no out dial. Isnt there any easy way to do that? I mean i have to play all ext for UNR and NCOS=0. Can i make new NCOS lets say CRNO=7 and assign it to some other FRL.
regards

TomasSouth · 04-16-2006, 01:53 AM

Try first my suggestion if it will works (as I am not also sure about it yet), then that is the time to get rid of the second problem which is "Isnt there any easy way to do that?"

Got a small priciple from my trainor, the more easy way you want for your users makes us the administrator the hard way.

justzikle · 04-16-2006, 02:08 AM

thats ok Tomas. i will get to the site tommorow and will try yours advice.
regards and take cares.

TomasSouth · 04-17-2006, 04:05 AM

How the tomorrow comes? (or tomorrow never dies?)

justzikle · 04-17-2006, 10:44 PM

Still away from the SIte. Trying to get there.

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Electronic Lock	Turkish	Meridian Systems	8	04-02-2008 01:11 PM
How can I change Interface type?	nlhtech	Meridian Systems	3	04-09-2006 10:06 AM
Time out for Electronic lock	Ric	Meridian Systems	2	10-17-2005 09:11 AM
Electronic Lock And Forwarding Calls at KX-TA616	gogon_gundrung	Panasonic	1	05-14-2005 03:55 AM
Compact ICS and PRI	pbxn	BCM and Norstar	6	04-08-2005 02:38 PM

Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)