612moto

ESN128
TYPE dsc
DSC
DSC 11
FLEN 0
DSP LSC
RLI 22
DSC 14
FLEN 0
DSP LSC
RLI 22
DSC 17
FLEN 0
DSP LSC
RLI 22
DSC 32
FLEN 0
DSP LSC
RLI 23
DSC 5
FLEN 0
DSP LSC
RLI 80
DSC 7
FLEN 0
DSP LSC
RLI 22
DSC 8
FLEN 0
DSP LSC
RLI 81

bigbadbillyc

So I see the DSC entry for 11 ---it will send calls to RLI22, but I don't see the DSC for 10? If they should all go the same place (route 5) then you should be able to add a new CDP entry:

TYPE dsc
DSC
DSC 10
FLEN 0
DSP LSC
RLI 22

The one thing that concerns me is that it looks from the traces like the Meridian was trying to route calls, but didn't have any digits to send. Something other than a DSC must be set up for 10 or else you did not include 10 in the post?

Fletch

What is the CDP Length set to in LD 86? Also you could try to add a FLEN of 4 on the CDP entry.

Fletch

__________________
Fletch

For more on Nortel E911 Solutions on the web:
http://nortel.com/e911

Don't forget to register for the FREE E911 Webinar on Oct. 30th!
http://thevoicereport.com/E911

612moto

We also have a CDP setup as 10, don't know how it wasn't showing in the above.

DSC 10
FLEN 0
DSP LSC
RLI 22
DSC 11
FLEN 0
DSP LSC
RLI 22
DSC 14
FLEN 0
DSP LSC
RLI 22
DSC 17
FLEN 0
DSP LSC
RLI 22
DSC 32
FLEN 0
DSP LSC
RLI 23
DSC 5
FLEN 0
DSP LSC
RLI 80
DSC 7
FLEN 0
DSP LSC
RLI 22
DSC 8
FLEN 0
DSP LSC
RLI 81


Changed to FLEN 4:


DSC 10
FLEN 4
DSP LSC
RLI 22

Still same result.
Strange when I dial the acod then 101010101070 ,,, it will complete the call.
Like something stripping 8 digits before passing the 1070 extension

612moto

We were just recently told from Nortel, that the problem is the ESS 5 protocol. When checking with the Cisco engineers on this they say no way.

Cisco says they don't route with that protocol.

Does anybody know about the ESS 5 or any of the other PRI protocols?

rwhite

I just tried to 'wade through' the full post so I hope I didn't miss something important and I'm sure someone will correct this if inaccurate, but-

If I understand the Meridians correctly the display you see using MSGO/MSGI may or may not be the actual interswitch conversation. It is the Meridian software talking to the Meridian hardware. To see the true total picture you need to have an independent monitoring device on the actual switch output to see if anything is being stripped.

612moto

Would a protocol have any affect on routing of calls 10xx out the PRI

bigbadbillyc

White is right about the MSGI and MSGO comments, but most places can't afford a T-Berd or protocol analyzer, so it is often the best you can do. As for the 5ESS vs DMS, both the Meridian and most pieces of Cisco Gear will allow you to configure either setting. Maybe it is worth changing them both just to try and prove that the protocol is NOT the issue. (Doesn't make sense to me, but I guess if you don't have anything else to go on it is worth a shot.) In Cisco gear you go to the configuration and do an isdn switch-type primary-5ess or isdn switch-type primary dms-100. Ask whoever takes care of your cisco gear for a printout of the running configuration and I can almost gaurantee you will see one of these commands in there. Tell them to try substituting the other one when you change, bounce both it and the Nortel end, and maybe we can see what will happen.

bigbadbillyc