A slight problem with my lab 11C - PBX Info :: Your Free PBX, PABX and Telephone Information Resource

***Archibald J. Cox*** · 12-22-2004, 08:14 AM

Hello all,

Had a little problem with my lab switch (single cabinet 11C 25.15)

Apparently there's some sort of corruption giving me some problems. The main problem is that I can't execute an EDD in LD 43. Here's the message I get when trying to do that:

Code:

>ld 43
EDD000


.edd

DB SEQ NUM = 5
CONFIG
PHYSICAL MAP
LTN TN
LTN LNK
TN
ASNCH
AML / ELAN
VAS
ARIES
FDL
SYSP
XPEC
XTDT
FTC
MCAD
FCAD
FDCT
LAPW
TIME
SPECIFIC DATA
  ALARM_MGT
CHECKING

RECORD COUNT =  0006

Starting internal database backup
to internal backup drive
Synching drives

BERR705 EXC 0: Bus Error in Task "tTapeTask" (0x203d5c70)
       SR=0x3008, PC=0x10147490, Addr=0x200000, SSW=0x525

SRPT789 RST 0: Exception-caused task restart: TID=0x203d5c70, vec=0x2, pc=0x10147490

SRPT789 RST 0: Exception-caused task restart: TID=0x203d5c70, vec=0x2, pc=0x10147490

SRPT786 RST 0: Task tTapeTask being restarted

SRPT786 RST 0: Task tTapeTask being restarted

Now at this point, it just hangs. It looks like the SL1 program has just stopped. I can, however, enter PDT and INI or SYSLOAD the system, so it's not completely dead. At that point, I get some nice information in the sysload messages which I will post here:

Code:

Meridian Small System Controller
Pre-Boot: 03   dev2.37
Flash Boot: NTDK34FA_r06  dev2.53
Reset Reason: 80, 4 - Reset due to CP invoked reset
SRAM: 128 kBytes
DRAM: 16 MBytes, speed=60 ns
Security ID: 10084904     type: NT_STD
System ID: 10084904
Backup Flash: 1572 kBytes
Program Store: 32 MBytes
Flash Drive: 8 MBytes
Expansion board #1 not installed.
Expansion board #2 not installed.
Ethernet MAC address: 00:00:75:45:65:62
PCMCIA card not installed in drive A.
PCMCIA card not installed in drive B.

*** To invoke install setup program from PCMCIA enter CONTROL-I ***

Executing power up self tests
Power up self test passed
DISKOS to be run.
Verifying Diskos.


*** OS RESTART ***


Meridian 1 X11 System Software
Release     : x112515
Created     : Thursday July 13 11:08:00 EDT 2000
Loaded      : 16/12/04 20:36:26

Copyright(C) 1972-1997 Northern Telecom, Inc.  All Rights Reserved.
VxWorks 5.2
Copyright(C) 1984-1995 Wind River Systems, Inc.  All Rights Reserved.
Use of the above software subject to terms of a license agreement.
U.S. Government users subject to "Restricted Rights" under FAR & DFAR.

Initialize Network Interface.
Network Interface is up.
Host         : PRIMARY_ENET
IP Address   : 137.135.128.253
Sub-netmask  : 255.255.254.0

Executing startup script "c:/p/etc/startupc".
# EDITION AK01, SL1LIB DAM.1439 (99/05/19 18:05:20) -- CLOSED
# Empty startup file for use in the field.
cd "c:/p/etc"
value = 0 = 0x0
0x2030ab4c (tRptD):  (16/12/04 20:36:28.216) BUG6358 zdrv: CRC check failed for partition: 0xa0000

Done executing startup script "c:/p/etc/startupc".

Loading retained patch from "c:/u/patch/p13135.p"

Loading retained patch from "c:/u/patch/p13167.p"

Loading retained patch from "c:/u/patch/p13214.p"

Loading retained patch from "c:/u/patch/p13247.p"

Loading retained patch from "c:/u/patch/p13213.p"
Activating patch, handle = 0
Modifying a longword at 0x20e35d48 from 0x0 to 0x105711a4
CMD_TONESTATES at 0x1057058a will be patched to jump to 0x20e35c94
Patch 0 has been activated successfully.
Activating patch, handle = 1
Modifying a longword at 0x20e37a12 from 0x0 to 0x10beb626
Modifying a longword at 0x20e37a0c from 0x0 to 0x10be79a4
Modifying a longword at 0x20e37a06 from 0x0 to 0x10be8f7c
Modifying a longword at 0x20e37976 from 0x0 to 0x10beb626
Modifying a longword at 0x20e3789a from 0x0 to 0x10beb626
Modifying a longword at 0x20e3781e from 0x0 to 0x10beb626
Modifying a longword at 0x20e377d2 from 0x0 to 0x10beb626
Modifying a longword at 0x20e377cc from 0x0 to 0x10beb626
PRT_VERSION at 0x10be77de will be patched to jump to 0x20e377bc
Patch 1 has been activated successfully.
Activating patch, handle = 2
Modifying a longword at 0x20e3883e from 0x0 to 0x102fbd2a
Modifying a longword at 0x20e38188 from 0x0 to 0x102fbe44
HOLD_INIT at 0x102faf8a will be patched to jump to 0x20e37f94
Patch 2 has been activated successfully.
Activating patch, handle = 3
PSWVVERSION at 0x10e6cbfe will be patched to jump to 0x20e39d46
Patch 3 has been activated successfully.
Activating patch, handle = 4
PSDL code at 0x109d2caa will be patched to jump to 0x20e39fd2
Patch 4 has been activated successfully.
0x2030ab4c (tRptD):  (16/12/04 20:36:28.218) BUG6335 Could not mount device "0x1009d87e".
Loading MAT script files......
Start SNMP agent

Loading SL1 data
Processed c:/p/data/view.cfg

SYS000 000808 000000 000000 000000 CPU 0
SYSDB RLS/ISS: 2515 LOADED FROM C: DATE/TIME: 16/12/2004 20:32:58 RECS: 6 SEQNO: 5
SYSLOAD RELEASE 25.15
FDL
DONE
INI000 00000000 20 37 03 00000000 00000000 00000000 00000000 00000000
                                                                      No CORPDIR*.CVS files in dir \u\db!
                                                                                                         Total n
umber of files 0

                 No csv files found!

DSET000 DOWN LOAD 0 0 0 0 0 0 0 97217

INI002 00000088


>
INI003 0000009C 000000A0 000000AF 000000B0 000000B4 000000B8 000000BC 000000CE 000000D0


INI003 000000D4 000000D8 000000EE 000000EF

SRPT750 INI 0: INI on side 0 due to System Cold Start

XMI002 2  XDLC

XMI002 8  XALC

XMI002 4

SRPT752 INI 0: INI completed in 16 seconds

I think the issue has something to do with the line that said: BUG6335 Could not mount device "0x1009d87e". Not to mention the one before that which said: BUG6358 zdrv: CRC check failed for partition: 0xa0000

To me it looks like it can't mount the backup flash drive and that's why it fails the EDD process.

Anyone have any ideas on how to fix this one without calling Nortel or replacing the SSC?

Thanks,
Arch

***John_In_Dakota*** · 12-22-2004, 08:43 AM

Holy crap!

Looks like you have issues. Good Luck and may the force be with you.

thedude · 12-22-2004, 08:52 AM

Perform a dummy upgrade and see where that gets you.

***Archibald J. Cox*** · 12-22-2004, 08:58 AM

Forgot to mention, steps I've already tried:

1. Install from LD 143 Upgrade menu
2. Install from bootup control-I install menu from 25.15 to 25.15
3. Restore from PCMCIA card (still can't write to the backup flash drive)
4. Restore from CCBR database file (Every time I type XRT in LD 143 or use the Upgrade menu to try this, the PBX INIs on me.)
5. In the process of "UPGRADING" from 25.15 to 25.15 right now. (most likely won't help)

Arch

thedude · 12-22-2004, 10:36 AM

Your SSC card is most likley bad as well as the Flash DB.

***Archibald J. Cox*** · 12-22-2004, 11:24 AM

That's what I figured. I've got a new SSC on order, if that resolves the problem then great, if not, then I guess I'll need a new DB too.

If anyone else has any ideas, they'd be greatly appreciated. I was wondering if anyone knew how to reformat the secondary flash partition? (It looks like that's the one with the problems)

Thanks guys,
Arch

thedude · 12-22-2004, 01:39 PM

Do you mean the Z drive ?
Your vendor may be able to do this.
I have had this error before and I was told if the reboot did not fix do a dummy upgrade.
If that did not fix the problem replace the SSC and the DB.
In my case the reboot worked fine.
At that time the machine was on 25.30 and now it is 3.0.
Give the SSC a shot what do you have to loose you have a captive switch.

imported_hafsteinn · 12-23-2004, 03:25 AM

Have you tried to erase the Z drive.
No harm trying
Go into PDT and do

zdrvEraseAll

Then try the EDD
Kari

***Archibald J. Cox*** · 12-23-2004, 08:42 AM

Thanks hafsteinn, I'll give it a shot and post back

Arch

***Archibald J. Cox*** · 12-23-2004, 08:49 AM

KARI! You ROCK!!

100% fully functional again.

Just out of curiosity, how does one learn about THAT command (or any others not listed in HELP)? I'd be interested as to what else I haven't been show.

Thanks again!

Arch

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Callpilot Apllication Problem	sneexy69	Meridian Systems	2	11-22-2003 11:23 AM
A LARGE PROBLEM	PP	Off Topic - Humor/Jokes	1	01-24-2003 02:36 PM
Strangest Problem Ever ?	markj39k	BCM and Norstar	11	01-15-2003 09:11 AM
OPT 11C T1 Problem	i05598	Meridian Systems	1	12-10-2002 10:05 AM

Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)