thedude

I assume your dch message is in reference to a ITG route ?

phoner

Actually no. The link is over IP using Cisco equipment. Basically I'm using the Cisco equipment as the CO. I have two Nortels programmed with QSIG links on each side. Calls route to the cisco equipment, get compressed and sent over our wan to the other site. Station to station calling works fine. This problem only appears if I dial a CDP which goes to our conference bridge T1. This T1 is a standard T1, no DCH. I checked all the access restriction and all appears to be ok. The weird thing is if I program a DISA number at the other site with the same CLS, NCOS and TGAR, I can make the call fine.

Any suggestions?

bassettb

If you are going through a CDP table then check the call type.
i.e. NNX, NPA UNCHANGED etc. It may be getting rejected because
the CISCO dosen't recognice the call type.

Fletch

Is this on an inbound or outbound message? Typically this is a NARS/BARS FRL or NCOS issue.

__________________
Fletch
Nortel Emergency Services PLM

For more on Nortel E911 Solutions on the web:
http://nortel.com/e911

Check out this month's E911 Talk podcast at Nortel E911 Talk Podcasts

phoner

This is an outgoing messge from the called side DCH. The other side gets a Cause #34: NO CHANNEL/CIRC AVAILABLE

All the phones have an NCOS of 5. All FRLs are 0 on the RLI. The class of service is mixed between UNR and TLD, neither can make the call. The number they are calling is a CDP that goes over to a DTI circuit which connects to a conference bridge. They can make calls to other CDPs which go to other Nortel ISDN PRIs in our network. They can also make calls to outgoing DTI circuits to our carriers.

I can make the call through a DISA number programmed with NCOS 5 and COS of TLD.

I tried the above suggestion of changing the call type to CDP, but the issue remained.

Fletch

I think your problem may be in the CALLED SIDE trunk NCOS/FRL. It is the one that needs the proper permissions to continue the call.

What is the trunk type of the inbound T1? Also what is the trunk type on the outbound to the Conference bridge?

Would also like to see your NET_DATA block (printed in LD 21)

__________________
Fletch
Nortel Emergency Services PLM

For more on Nortel E911 Solutions on the web:
http://nortel.com/e911

Check out this month's E911 Talk podcast at Nortel E911 Talk Podcasts

phoner

Here's the incoming trunk route:

TYPE RDB
CUST 00
ROUT 34
DES
TKTP TIE
NPID_TBL_NUM 0
ESN NO
CNVT NO
SAT NO
RCLS EXT
DTRK YES
BRIP NO
DGTP PRI
ISDN YES
MODE PRA
IFC ESGF
SBN NO
PNI 00034
NCNA NO
NCRD NO
CHTY BCH
CTYP UKWN
INAC NO
ISAR NO
CPFXS YES
DAPC NO
INTC NO
DSEL 3VCE
PTYP PRI
AUTO NO
DNIS NO
ICOG IAO
SRCH LIN
TRMB NO
STEP
ACOD 6934
TCPP NO
TARG
CLEN 1
BILN NO
OABS
INST
ANTK
SIGO STD
ICIS YES
TIMR ICF 512
OGF 512
EOD 13952
NRD 10112
DDL 70
ODT 4096
RGV 640
GRD 896
SFB 3
NBS 2048
NBL 4096
TFD 0
DRNG NO
CDR NO
MUS NO
EQAR NO
FRL 0 0
FRL 1 0


PAGE 002

FRL 2 0
FRL 3 0
FRL 4 0
FRL 5 0
FRL 6 0
FRL 7 0
OHQ NO
OHQT 00
CBQ NO
AUTH NO
TTBL 0
ATAN NO
PLEV 2
ALRM NO
ART 0
SGRP 0
AACR NO

Here's one of the trunks:

TN 034 08
TYPE TIE
CDEN SD
CUST 0
TRK PRI
PDCA 1
PCML MU
NCOS 7
RTMB 34 8
B-CHANNEL SIGNALING
TGAR 0
AST NO
IAPG 0
CLS CTD DTN CND WTA LPR APN THFD HKD
P10 VNL
TKID
DATE 2 DEC 2004

Here's the conference bridge T1 route:

TYPE RDB
CUST 00
ROUT 50
DES CONF BRIG
TKTP TIE
NPID_TBL_NUM 0
ESN NO
CNVT NO
SAT NO
RCLS EXT
DTRK YES
BRIP NO
DGTP DTI
ISDN NO
DSEL VCE
PTYP DTT
AUTO NO
DNIS NO
ICOG IAO
SRCH LIN
TRMB YES
STEP
ACOD 6950
TARG
CLEN 1
BILN NO
OABS
INST
ANTK
SIGO STD
STYP SDAT
TIMR ICF 512
OGF 512
EOD 13952
DSI 34944
NRD 10112
DDL 70
ODT 4096
RGV 640
GRD 896
SFB 3
TFD 0
SST 5 0
NEDC ETH
FEDC ETH
CPDC NO
DLTN NO
HOLD 02 02 40
SEIZ 02 02
SVFL 02 02
DRNG NO
CDR NO
MUS NO
MANO NO
EQAR NO
FRL 0 0
FRL 1 0
FRL 2 0
FRL 3 0
FRL 4 0
FRL 5 0
FRL 6 0
FRL 7 0


PAGE 002

OHQ NO
OHQT 00
CBQ NO
AUTH NO
TTBL 0
ATAN NO
OHTD NO
PLEV 2
ALRM NO
ART 0
SGRP 0
AACR NO

Here's one of the trunks:
DES
TN 008 01
TYPE TIE
CUST 0
TRK DTI
PDCA 1
PCML MU
NCOS 7
RTMB 50 1
TGAR 2
SIGL EM4
STRI/STRO WNK WNK
SUPN YES
AST NO
IAPG 0
CLS CTD DTN CND ECD WTA LPR APN THFD HKD
P10 VNL
TKID
DATE 13 NOV 2001

Here's the RLI that points to the conference bridge (all three routes are programmed the same and go to the bridge)

RLI 36
ENTR 0
LTER NO
ROUT 50
TOD 0 ON 1 ON 2 ON 3 ON
4 ON 5 ON 6 ON 7 ON
CNV NO
EXP NO
FRL 0
DMI 0
FCI 0
FSNI 0
SBOC NRR
OHQ NO
CBQ NO

ENTR 1
LTER NO
ROUT 51
TOD 0 ON 1 ON 2 ON 3 ON
4 ON 5 ON 6 ON 7 ON
CNV NO
EXP NO
FRL 0
DMI 0
FCI 0
FSNI 0
SBOC NRR
OHQ NO
CBQ NO

ENTR 2
LTER NO
ROUT 52
TOD 0 ON 1 ON 2 ON 3 ON
4 ON 5 ON 6 ON 7 ON
CNV NO
EXP NO
FRL 0
DMI 0
FCI 0
FSNI 0
SBOC NRR
OHQ NO
CBQ NO

ISET 2
NALT 5
MFRL 0
OVLL 0


Here's the NET_DATA

TYPE NET_DATA
CUST 00
OPT RTA
AC2
FNP YES
ISDN YES
PNI 1
PINX_DN
PFX1 610
PFX2 617
HLOC
LSC
RCNT 5
PSTN NO
TNDM 15
PCMC 15
SATD 1
OCLI NO
TRNX YES
EXTT YES
FTOP FRES
VNR NO
NIT 8
FOPT 14

Fletch

Out of curiosity why are your ITG trunks TGAR 0 and your Conference bridge TGAR 2?

__________________
Fletch
Nortel Emergency Services PLM

For more on Nortel E911 Solutions on the web:
http://nortel.com/e911

Check out this month's E911 Talk podcast at Nortel E911 Talk Podcasts

phoner

Actually the trunks are not ITG, they are programmed as QSIG. I changed the QSIG trunks to TGAR 0 in case it was causing an issue.