| |||||||||
 |
| ||||||||
| |||||||||||||||
| |||||||||||||||
| Meridian Systems Welcome to the Nortel Meridian Forums Including Meridian Options 11-81C CS1000M Meridian Mail Call Pilot Companion and Sucession Hospitality OTM MAT MICB RAN NetGateway ..., and all other Applications |
| Tags: assign, ccbs, rcap |
  |
| | LinkBack | Thread Tools | Display Modes |
 11-10-2004, 03:29 PM | #1 (permalink) |
| Junior Member | I'm trying to assign a RCAP CCBS to a T-1 QSIG trunk. Here is my Adan Dch 17 configuration. ADAN DCH 17 CTYP TMDI CARD 01 PORT 1 DES avyaqsig USR PRI DCHL 1 OTBF 32 PARM RS232 DTE DRAT 64KC CLOK EXT IFC ISGF PINX_CUST 0 ISDN_MCNT 300 CLID OPT0 CO_TYPE STD SIDE NET CNEG 1 RLS ID 6 RCAP COLP NDI CCBO DV3I QMWI MBGA NO OVLR NO OVLS NO T310 120 T200 3 T203 10 N200 3 N201 260 K 7 I want to assign a CCBS-Call Completion feature to the RCAP, but keep getting this error: SCH0531 Unable to match input with stored mnemonics. The RCAP prompt in overlay 16 has been answered NDS when QSUr QSIG GF are not accessible or with an inappropriate interface configured (e.g. Sl 1). Action: Reconfigure accordingly. Severity: Info Here is my RDB info: REQ: prt TYPE: rdb CUST 0 ROUT 51 TYPE RDB CUST 00 DMOD ROUT 51 DES AVAYAQSIG TKTP TIE NPID_TBL_NUM 0 ESN NO CNVT NO SAT NO RCLS EXT DTRK YES BRIP NO DGTP PRI ISDN YES MODE PRA IFC ISGF SBN NO PNI 00001 NCNA NO NCRD NO CHTY BCH CTYP CDP INAC NO ISAR NO CPFXS YES DAPC YES TBL 0 INTC NO DSEL 3VCE PTYP PRI AUTO NO DNIS NO DCDR NO ICOG IAO SRCH LIN TRMB NO STEP ACOD 5012 TCPP NO TARG 01 CLEN 1 BILN NO OABS INST ANTK SIGO STD ICIS YE TIMR ICF 512 OGF 512 EOD 13952 NRD 10112 DDL 70 ODT 4096 RGV 640 GRD 896 SFB 3 NBS 2048 NBL 4096 TFD 0 DRNG NO CDR NO MUS NO PAGE 002 EQAR NO FRL 0 0 FRL 1 0 FRL 2 0 FRL 3 0 FRL 4 0 FRL 5 0 FRL 6 0 FRL 7 0 OHQ NO OHQT 00 CBQ YES NDIG 02 AUTH NO TTBL 0 ATAN NO PLEV 2 ALRM NO ART 0 SGRP 0 AACR NO _____ Can someone let me know how I can assign CCBS feature on my QSIG T-1 trunk? |
 |   |
| 11-10-2004, 11:19 PM | #2 (permalink) |
| Senior Member  | You cannot do CCBS in the release you are running. You may be getting this from some pre-Release 24 NTP's, or an older Avaya configuration whitepaper. Currently you have CCBO defined in your RCAP, and in talking to the Avaya you are going to need Integer Value coding or CCBI. Remove the CCBO from the RCAP by doing XCCB at the RCAP prompt. You will then be able to add CCBI to the RCAP. Also while you are in there, get rid of the RLS ID of 6. It is not doing anything for you. Remember Q.Sig in machine agnostic, and therefore if any vendor can be on the far end, RLS ID is sort of a moot point. The one exception to this rule is when running Q.Sig to another Meridian. Then BOTH sides should have the lowest common RLS ID between the 2 switches. For example a Release 25 switch talking to a Release 24 switch would have '24' as the RLS ID on BOTH sides. By putting a '6' there, you are confusing the Nortel to think that a Release 6 Nortel is at the far end. That's a ways off I think  Generally the Avaya likes 'I'nteger Value coding RCAP settings opposed to 'O'ject ID coding options on their Q.Sig integration. The 'S' values in the RCAPS are no longer used. These would try to inteligently identify if the remote side was using Object ID Coding, or Integer Value coding. This option did not always resolve correctly, and as part of the Q.Sig compliance code initiative done in Release 24, this option was removed and replaced with hard settings to avoid misconfiguration. Good question! I miss not being able to answer these as much as before! |
| | |
| |
| Currently Active Users Viewing This Thread: 1 (0 members and 1 guests) | |
| Thread Tools | |
| Display Modes | |
| |
 Similar Threads | ||||
| Thread | Thread Starter | Forum | Replies | Last Post |
| HELP..NAM...Minuet ACD...Can't assign agents to groups....!! | hotextec | BCM and Norstar | 4 | 12-05-2003 03:43 AM |
| RCAP in LD 16 | gei_spot | Meridian Systems | 3 | 12-23-2002 12:07 AM |
| RCAP in LD 16 | gei_spot | Meridian Systems | 7 | 12-19-2002 04:49 PM |
Linear Mode
