| |||||||||
 |
| ||||||||
| |||||||||||||||
| |||||||||||||||
| Definity Support Definity Servers Support |
| Tags: link 1 |
  |
| | LinkBack | Thread Tools | Display Modes |
| |||||||||
|
| ||||||||
| |||||||||||||||
| |||||||||||||||
| Definity Support Definity Servers Support |
| Tags: link 1 |
| |
| | LinkBack | Thread Tools | Display Modes |
 04-29-2008, 08:06 AM | #3 (permalink) |
| Junior Member | We have reseated the card. Went through the same. This is a new card too. We have a G3si running in V 11 pretty old stuff. When I do >status link it comes out as restarting under status and has in-service/idle in service state. All the other data is loaded correctly. One thing I did today, I did another >test port and it came up with ETH-Prt Error Code = 7 but could not find in any of my documentation. |
 |   |
| 04-29-2008, 10:12 AM | #4 (permalink) |
| Moderator  | Is this a brand new card or are you replacing an existing card? If it is a new card have you done all the programming for it? Is it added in node names, ip interfaces, is the data port added? What is link 1 supposed to be doing? __________________ Do not meddle in the affairs of dragons for you are crunchy and taste good with ketchup. Marty |
| | |
| 04-29-2008, 02:45 PM | #5 (permalink) |
| Junior Member | I am not sure on this one, but from the error code it looks like it is trying to state an ethernet port error. Per what Marty stated, have you double checked your programming and is everything wired correctly? I am going to guess that there are no license issues. I hope you figure this out and let us know what the error was. Good Luck, 2wire |
| | |
| 04-30-2008, 07:48 AM | #6 (permalink) |
| Junior Member | In reply to Y'alls questions: Is this a brand new card or are you replacing an existing card? We just replaced a suspected bad card If it is a new card have you done all the programming for it? Checked all the programming, Port 17 on the TN799DP is assigned. All checks good Is it added in node names, ip interfaces, is the data port added? All of these were previously programmed, everything checks out good What is link 1 supposed to be doing? Link 1 is our port into the switch for network management data and remote access Our IT folks has a router on this link and this was the original complainant, they said that they did not have a link light on the router and they had the switch tech replace the card ( After doing their troubleshooting on the router). When they replaced the card they had the same problem. I suspect that the original problem was this card was stuck on restart. When they replaced it there was no change in the problem. Then that's when they gave me the trouble. |
| | |
| 04-30-2008, 10:23 AM | #7 (permalink) |
| Moderator | Have your network guys verify that the router port that your CLAN is attached to is locked to 10M/half duplex. Also make sure that the CLAN is also set for this speed. Do not use autosensing at either end. Does this do anything? __________________ Do not meddle in the affairs of dragons for you are crunchy and taste good with ketchup. Marty |
| | |
| |
| Currently Active Users Viewing This Thread: 1 (0 members and 1 guests) | |
| Thread Tools | |
| Display Modes | |
| |
 Similar Threads | ||||
| Thread | Thread Starter | Forum | Replies | Last Post |
| restart/reboot/whatever | rodrigo_in_Brasil | Meridian Systems | 3 | 03-13-2008 03:22 AM |
| Pbx restart | moxxxa | Hicom/HiPath | 4 | 05-15-2007 02:27 AM |
| OS Restart | norstarrr | Meridian Systems | 3 | 03-06-2007 07:03 AM |
| restart command | ymbet | Meridian Systems | 3 | 03-20-2006 12:34 PM |
| Meridian Link > Symposium Link | deb321 | Meridian Systems | 2 | 09-25-2003 03:26 PM |
Linear Mode
