rustynails

This is the serial port log. Can anyone tell me if this is hosed, or can be repaired? Is it software or Hardware. At the end of the log it reads "access failed to start, reboot in 120". any help would be appreciated.


CallPilot 150 Boot Loader V1.5.19
(C) 2001 Nortel Networks

--------------------------------------------------------------------------
NETWORK INTERFACE PARAMETERS:
IP address on LAN is 170.70.1.35
LAN interface's subnet mask is 0xffffff00
IP address of default gateway to other networks is 170.70.1.254
HARDWARE PARAMETERS:
Serial channels will use a baud rate of 9600
This board's ethernet address is 0:60:38:BF:9:3B
CALLPILOT BOOTLOADER PARAMETERS:
Execution Mode: Load CallPilot
Source File System Parameters:
Device: ATA Disk
Source File List Name:
Destination File System Parameters:
Device: ATA Disk
File List Name: filelst.lst
Format Target Device: Y
Boot File Name: CallPilot.bin
After board is reset, start-up code will wait 2 seconds
--------------------------------------------------------------------------
To change any of this, press any key within 2 seconds


Automatic Update Mode Enabled!
To Change Update Mode to Manual, press any key within 10 seconds
Updating in Automatic Mode!

Initializing ATA Disk... Done.
Initializing PCMCIA Stack ...SSInit: CS_Sockets - 2,Num_PWindows - 8
Card services Init complete found 2 sockets.
Done.
Initializing PCMCIA ATA Disk Drives ...SanDisk SDP 5/3 0.6
AtaInit: completed
Done.
Detecting ATA Cards...
Device found in Slot A:
Model: SanDisk SDCFB-192
Serial: 111516K1502E0735
Rev.: Vdg 1.25
Mounted 10.256
Loading 10.256/CallPilot.bin... Done.
Unmounting 10.256
Transferring control to the downloaded code

I-Cache ON, D-Cache ON
Downloaded OS and application executing from RAM
Memory Test Completed Successfully
Starting root(RAM)
Initializing D-channel driver
Initialized for 8 channels
Disk volume 3.0.0, initialized...
Initializing ATA Disk... Done.
Initializing PCMCIA Stack ...SSInit: CS_Sockets - 2,Num_PWindows - 8
Card services Init complete found 2 sockets.
Done.
Initializing PCMCIA ATA Disk Drives ...SanDisk SDP 5/3 0.6
AtaInit: completed
Done.
Detecting ATA Cards... Card(s) detected
Verifying 7.0
PPP: Using hardcoded ip address 192.168.0.2
PPP: Username is CallPilot
PPP: Password is administrator
PPP: Adding PPP NI...

Standard output device initialized...
Pseudo device initialized...
7.1\safe not found
TFTP device initialized...

Login:

Type "test" to stop auto boot

Starting Access/2 and Voicemail
SysConfig file does not exist. Use default!!!
Opening DSP Msg logfile
DSP[0]: 1.50.35.A2 Jun 05, 2002
DSP[1]: 1.50.35.A2 Jun 05, 2002
DSP Abstraction Layer Binding to port 5001
DSP Abstraction Layer Accepting...
Language Debug: Reading '7.1\access2\runtime\alarm0.dat'.
Read language file '7.1\access2\runtime\alarm0.dat'.
Loaded 1 of 1 language file(s). Default language: 0 (hex).
Curr File Pool Path='7.0\access2\FILEPOOL\0\*.*'
Curr File Pool Path='7.1\access2\FILEPOOL\0\*.*'
OSA DBG: pSOS_ERR: ResumeTask - t_resume rc =15
TCM 1: Channel 0: UP
CH0 is opened.
TCM 2: Channel 2: UP
CH2 is opened.
TCM 3: Channel 4: UP
CH4 is opened.
TCM 4: Channel 6: UP
CH6 is opened.
DCHCNTRL - DCH0 Reader created
0arser sync'ed up
DCHCNTRL - DCH1 Reader created
2arser sync'ed up
DCHCNTRL - DCH2 Reader created
4arser sync'ed up
DCHCNTRL - DCH3 Reader created
6arser sync'ed up
DCHCNTRL - Number of D-channels trying :4
dchMon: Initialized FumpSTM of Dchannel No : 3
dchMon: Initialized FumpSTM of Dchannel No : 1
dchMon: Initialized FumpSTM of Dchannel No : 2
dchMon: Initialized FumpSTM of Dchannel No : 4
DCHCNTRL - Active channel = 4 D Channel State = 255

dch: channel 4 Msg Len 99 Update Board to Access

dch: channel 4 Msg Len 99 Update Board to Access

dch: channel 4 Msg Len 99 Update Board to Access

dch: channel 4 Msg Len 99 Update Board to Access
D-channel No. 2 is working
D-channel No. 1 is working
D-channel No. 3 is working
D-channel No. 4 is working
2:receive unknown msg c0
2arser sync'ed up
Got KSU Version from functerm: ----30BwE02F|
Access logging disabled
SYS: Access failed to start, system will restart after 120 seconds
SYS: To stop rebooting, enter stopreboot
***>>>TelInit telNumITInfoElemBytes 5

******************
* *
* ! R E A D Y ! *
* _ *
******************
--------------------------------------------------------------------------------
Posts: 174 | From: toostoned, arizona | Registered: Apr 2001 | IP: Logged |